This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
Hi,
Can I use the serial interface to interact with an nRF52840 dongle running a mesh stack?
If so is this limited to UART or can the USB connectivity be used?
If any...
Hi,
I am developing a device based on NRF52840 soc in ble central mode. Could I claim when I do not call sd_ble_gap_scan_start function BLE radio is thoroughly OFF and there...
Hi everyone,
Maybe this is a very simple question but I want to avoid future troubles, that's why I'm asking. I want to copy an example from SDK16 and rename it. For example...
My Win 10 is up to date. Seger' J-Link driver is OK. Here's message from log screen: Please help to find what I missed. Thanks.
08:03:35.048
Using nrfjprog library 10...
Hello,
I am currently trying to use the MQTT publisher example to send a message to a locally hosted MQTT broker (I assume I can use a local IPv6 address?). The MQTT broker...
Hey Nordic Team,
I'm in the midst of integration the nRF91. As with the nRF52 designs, less work was taken out of the RF design aspect because it has a built in balun. As...
Hi Nordic：
I burned the AP & Modem firmware in the picture below, and found that the current consumption when entering PSM is 500μA. Please help to analyze. What caused...
Hello ,
I am using freertos with nrf uart service, i could able to get these timings that seem little bit weird.
one of the pin toggled for each successful ble_nus_data_send...
Hi Nordic ,
I have a nRF52840 project development based on SDK 15.3 . Now ,I need to add DFU feature there. we suppose to use background DFU here. we will use long range...
We have been using RSSI as a signal for doing location services, however we are find that a bit challenging. From reading the literature in the field, several researchers...
Dear community,
for my upcomming project I would like to use the nRF52832. Since there also exists a development kit I started to make myself familiar with Embedded Studio...
I have two nrf52 chips connected to each other via SPI
I send data from my Nordic Uart app to my nrf52 chip 1 and I want to send the data that I receive from Mobile app...
Hi,
I'm trying to prepare the firmware for a nRF24LU1+ in order to allow automatic driver installation on Windows.
Based on Microsoft documentation during device enumeration...
I like to provision a node in mesh with the help of computer. Shall i use serial example? Is it possible to use without interactive_pyaci to provision a node with computer...
