Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
Hi, I'm using nrf52840 TWI master. Sometimes the I2C bus result as locked in endless loop to retry the start conditions. I see that in this case SDA and SCL are tied low for...
Updating the SoftDevice on the nRF52832 from S132 v2.0.x to S132 v3.0 using the Dual Bank Bootloader from SDK v11.0.0 results in the application not starting up after the...
I am planning to use Open bootloader example as my starting point for adding a bootloader to an application. I donot want Softdevice. Initially I am going to check the dfu...
i am working on ble_app_uart central and peripheral, so basically peripheral will sleep wake up and send advertisement packet to central . Now the issue is if peripheral is...
Hi, My Lord. When I run the example, I use short-name(BLE_ADVDATA_SHORT_NAME) advertising always "Fatal error",It's no use reducing payload.
On the other hand, how to add...
Dear experts..
I'm currently developing and testing nRF52832 application with nRF52-DK.
This are three questions about "actual" advertising packet length on air.
First...
1.HOW TO enable a node relay , friend,proxy or low power ability ?
2.if node A publish a message to a GROUP ADDRESS(0XC001) for node B( subscribeed this group address) ...
I looked at the nRF91_DK_User_Guide and it is very confusing to understand how to set up the board for current measurements. The figure says to solder SB44 and SB45 but the...
Hello,
As of today, April 17th 2019, I am using latest version of SDK and SES. I am using Jlink from nRF51DK and a nRF52832 module bought from ebay.
I tested several examples...
extern void bsd_recoverable_error_handler(uint32_t error) AND
extern void bsd_irrecoverable_error_handler(uint32_t error); Will return various error codes - is there a list...
I'm trying to use the NUS to send data over from NRF52 dev kit to the NRF Connect app. Using Putty for UART works fine. Now I adapted to read out ADC values from 2 ADC ports...
Hi, can someone tell me what chip this is and where I can find the data sheet? Or at least if this is a custom fabrication, what chip from Nordic is it based off of? Thanks...
Hello,
I am using ble_app_uart_c example for my nRF52832 based central application. I would like to modify Tx Power and MODE of my device.
As per datasheet, I should write...
I'm finding above examples in SDK example file. but, can't find.
where the perfectly tutorials?? It's too hard for me only refer to the library's code.
I cannot config...
