I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi,
currently I am trying to figure out how to disable the cryptocell hardware after enabling it, because if I enable it and then enter systemOFF, the system still draws...
Hello,
I am using NRF52840 Preview DK, I am running peripheral/SAADC example on the board, I shorted Channel 0 and GND on the board and I am receiving negative values...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hi
Using SD Version 6.1.1 and NRF Version 15.3.0.
Using the following advertising params I can set non-extended advertising
ble_gap_adv_params_t advertisingParameters;...
Hello Nordic support, For long term power profiling of nrf52 hardware, I am using the suggestion given here, that makes use of functions in python script ppk.py: https://devzone...
Hello Nordic Team,
I have an application in development where some bigger files (~20kb) can be downloaded into the device, so they get stored in with the FDS system.
Now...
Hi,
I am using BLE application in NRF52832 board and using NRFConnect app to send custom characteristic service from mobile app to nordic device. But if I am sending a data...
I updated Thingy:52 to firmware version 2.2.0 using the Thingy:52 Android app.
WIth the Thingy:52 running v2.2.0, the WebApp for Thingy:52 can pair with Thingy:52 but it...
Hello Sirs,
We implemented a joint bandwidth test (or speed test) for a radio channel by transmitting notifications.
Parameters set in SDK config:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
I am following the instructions at infocenter.nordicsemi.com/.../nRF52840_PDK_User_Guide_v1.2.pdf to program a pre-compiled example (blinky).
I have two nRF52840-PDK (PC10056...
Hi, im designing a beacon based on nrf52832, but i have a question about RF section, i´m using 2450AT18B100E chip antenna, and to match it with the nrf52 i'm following the...
Hi,
Trying to investigate eddystone protocol. After compiling and uploading ble_app_eddystone example I see Eddystone BLE device in non-connectable mode.
But after pressing...
I am using NRF52840 DevKit on Ubuntu 18.04 (bionic). I have successfully compiled pc-ble-driver and hex connectivity/softdevice.
I have now download pc-ble-driver-py and...
