Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Dear every one.
My company has ordered 20 development kit NRF52840 for our Mesh project. We will receive these board 1 week later.
But i have 1 preview development kit...
Could you please help me out on how to read my EMG sensor values and display it via the Nrf tool box. I have a redbear nano v2 and the digital output of the sensor is received...
Hello,
I'm having some issues with the MAXCNT limitation of 256bytes because I want to send larger packets and receive packets through the SPI Slave interface, which is...
I have an external board based on nRF51822 QFAC. I have a nRF52 preview DK. Will it be possible to detect my external board if connected via the preview DK. I tried and the...
Hello,
We've a Custom board based on nRF52832, it works fine in beacon mode using the Synth Clock (else it doesn't work):
// <o> CLOCK_CONFIG_LF_SRC - LF Clock Source...
When using the PPK to measure the current of our custom hardware the lowest range doesn't give logical results. (Either the PPK python GUI or nRF connect) When the nRF52 on...
Reference: nRF52840 DK Evaluation Board Schematics
The following inductors are lised in the schematic:
L1
3.9 nH
High frequency chip inductor ±5 %
0402 ...
I am working on windows xp command prompt and using nrfutil version 3.5.1
I want to do a Device Firmware Upgrade over BLE through my nRF52 DK board on a custom element....
Hi there,
SPIM3 running at max speed (32MHz) will be the fastest external interface (along with QSPI)
Because I would like to make to most of it, I wondered if you had...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hi,
Please help me on the nRF52840 UARTE RTS signal, through the doc: "nrf52840_ops_v0.5.pdf", we can know if we stop the UARTE RX by trigger the "NRF_UARTE_TASK_STOPRX...
Hi Sir,
I hope to add ble_nus and ble_nus_c into Central_and_Peripheral projects (ble_app_multirole_lesc and ble_app_hrs_rscs_relay), I use SDK 15.0.0 and nRF52832.
...
Hi,
When I developed with the board of nRF52840, I met up with an issue of UART. Sometimes, the UART will get a DRV_ERROR and crashed. Does anyone meet up with this issue...
