When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi,
I'm wondering if there is an example for scanning and advertising at the same time during a connection as peripheral? Or is there an example where I can start from...
Hi, trying to upgrade from V12.3 to V14.2 with a nrf52382 and SD 132.
I'm stuck with nrf_sdh_ble_enable returning an error code - unfortunately, the SDK documentation does...
Hello,
I will be using the NRF52 to send out advertising btle packets.
I am curious if anyone has any idea if the radio is strong enough to still send out packets if...
Hello
Is there any possibility to get receiver IF to any package pin. Even some kind of factory debug mode.
Normal receive functionality during this is not needed.
...
Greetings, we're currently working in an application where we need to connect different peripherals to a nrf52832 for a wearable device. Each of these peripherals uses a different...
Hi:
i write very simple BLE App, it used open link. No security/encrypt. 1 service with 2 characteristics.
tx(serviceTXID, rxBuffer, 0, sizeof(rxBuffer), GattCharacteristic...
Hi there,
I wonder why I have to flash my nRF51 DK using mbed build first to make the SDK build work?
I received my 2 nRF51 DK today and I tried the first one in the...
Hello
I am new to Nordic's product line. I would like to know if there is a recommended Bluetooth 5 SoC for wearable products that require years of battery life. For example...
Hello, I am trying out my pca10028 board, with s110 and my updated ble_app_uart expample. I am trying to detect a link loss: board advertises as peripheral connects with android...
Hello,
I work on module BLE LAIRD BL652 and I'm a BLE peripheral. I have tried to make a BASIC program for advertising while in a connection but without success.
As...
Hi,
i am creating a new project iar workbench 7.8 with SDK V8.1.0 and softdevice V8.0.0 using custom board nrf51822 ic revision 3 (QFAAH00),clock source as "NRF_CLOCK_LFCLKSRC_RC_250_PPM_8000MS_CALIBRATION...
Hello Sir,
I am designing PCB using nRF52832 SoC it is very small and operated on AA battery source.
So please recommend me for reverse battery voltage protection diode...
Hi Guys,
Me again. I was thinking someone could provide some suggestions on my understanding of the BLE connection ( porfile, GATT, characteristic,value, etc...)
I finished...
I had successfully write a structure data to fds. After which, I would like to update the same file and record key with new values of a structure. After updating, I will read...
