hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
When I take a vanilla Objective C Xcode project and try to convert it to Cocoapods for an iOSDFULibrary with Xcode 9 results in an unopenable project. You get an error...
Hi,
I am using nrf52832 to scan beacons and then store temporary into two dimensional array.
I made interrupt that call after some interval to send stored beacons over...
Hello,
I got two device with DFU-OTA service enabled
(included device manager and dfu related handlers/files; merged the application, dual-bank bootloader, s130, app_valid_setting...
Using GCC compiler with Eclipse, sdk v14.1, nRF52832, in ESB protocol mode.
The code compiles and builds just fine, all links are ok, but the code below issues a syntax...
One of my nRF52-DK started to act oddly - very brief message in red type flashed up by nRFgoStudio on programming a few times - unfortunately too fast for me to read.
Now...
Hello,
I'm trying to build the ble_ant_app_hrm (multiprotocol) example, using SDK v14.1.0
Here is the output I get, after running make :
Makefile:216: Cannot find...
Is possible use the PPK with a custom board to measure the current usage?
In the pictures it looks like has headers to attach the nRFxxDK modules. but what about custom...
When configuring my Bluetooth Mesh server node to the network, it receives an error and I am not sure why.
I receive an ACCESS_STATUS_INVALID_MODEL error after having called...
Hi,
I am aware of how to use nRF51 sniffer with wireshark.
But in my current project, I am not able to sniff data packets. I am not sure which BLE stack is used in the...
Hi,
we have implemented the experimental_writeable_ndef_msg example from SDK12.2 with Nordic NRF52 on a custom board. Reading the NDEF Message works fine with smartphones...
Nordic nRF52832 chipset
Battery operation such as CR2477 Lithium Manganese primary button cell.
Many application circuits show this microcontroller used with a button...
Greetings,
One thing I've noticed is that if I enable the RTT nRF_Log messages in the bootloader, then the RTT messages that are being sent out in my application do not...
Hi,
i have recently bought a development kit for the nRF24LE1 chip. Untfortunately there was no CD included, as described in the following user guide.
data.icbank.com/...
The nRF51822 Bluetooth Smart Beacon Kit has P0.09 and P0.11 connected to the programming connector P2 (Pin 3 and Pin 6). From the User Guide :
Can I use them as UART...
I have a Rigado BMD-300 Evaluation Board with a BMD 301 module attached. Using the Texas Instruments SmartRF Packet Sniffer, I see the message being broadcast approximately...
