hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
I mashed up RTC and SAADC examples. The files of the project are attached in the end of the post. The problem is that after the first iteration (I want to sample audio for...
Hello,
I am using developping on an nRF51822 with SDK12. In our application, our custom board need to communicate with a computer through a USB communication. I am not...
I'm working on the product using the nRF51422 QFAAE00 , SD110_nrf51_8.0.0, SDK 10.0.0. My product has the advertising flow as below
The device advertises forever...
Hello!
I have a problem when scanning and advertising at the same time with a NRF51822 and S130 v.2.0.0. (SDK11).
I can start both scanning and advertising without any...
Hello,
I am designing a PCB layout using nRF52832, I want to make it as small as possible so I am considering to route all component tracks to another layer.
I want...
Hi,
For an application I have a nRF51 at my disposal and I need to transfer about 3'000Bytes. I found in the documentation that the nRF51 can use the S130 SoftDevice which...
Hi.
Using PCApp/MCP(v 3.10.0.14), How can "BLE_GAP_EVT_SEC_INFO_REQUEST" occur?
Or will not it occur?
If it occurs, please tell me how to do it.
Thank.
Hello,
I need help about the multirole with the Freertos.
When I take the code example from Nordic "C:\Nordic\nRF5_SDK_13.0.0_04a0bfd\examples\ble_central_and_peripheral...
Example project: blinky_FreeRTOS_pca10028.uvprojx
I include SEGGER_RTT.h file.
After execute vTaskStartScheduler() function.
SEGGER_RTT_printf(0, "Hello World from SEGGER...
Using C11 compiler, and a Makefile from a template, where the Makefile defines CFLAGS with -Werror I get:
.../components/libraries/util/app_error.c:47:5: error: narrowing...
I running the (nrf52) HRM profile with FreeRTOs and connecting the BLE device with the Nordic Toolkit app.
On occasion the connection to the BLE device fails. After repeated...
Hi, I want to interface BLE module with freeRTOS. Does nordic provide BLE stack for freeRTOS? and if yes then is it opensource? or is there any standard BLE stack which can...
Hello,
I want to design PCB antenna for nRF52832 chip. I took reference from nRF51 dongle hardware layout.
I wanted to spread antenna upto 18mm width so I reduced the...
Hi
The j-link detects the chip, but for not obvious reason the j-link and keil will trough an error when I want to program the chip, here is the j-link out put. do you have...
