Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am having hard times to make SAADC working on DK-52, SDK13, S132. I need to perform a voltage measurement on command received from a connected device.
AIN pin...
Hi All
I am looking for the way to send and receive the string between nrf52 and mobile app.
what are the possible ways to do with minimum power consumption.
main concern...
Hi,
I've allready read a lot about using a static passkey on the DevZone and I have tried tons of things, but I just can't get it to work.
What I want is to connect...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi, I am playing with the SDK13 examples, UART (w/o softdevice). I use gnu gcc. The example runs and when I type q or Q the code goes to the printf(" \r\nExit!\r\n") as designed...
Hi
I read somewhere that when using internel ref for analog measurements the Vin changing does not influences the analog reading. Is that true?
Please, consider the circuit...
Hello,
I am looking through the data sheet for the NRF52 and do not see anything for writing to NVMC.
I see you can erase and configure the NVMC using:
NRF_NVMC ...
Hello, i'm using a microcontroller connected to a nrf24l01p in rx mode,after receiving a packet it writes the ack for the next transaction,it only works if i add a delay ...
hi i am unable to find cause of issue i am working on BLE and PWM driver when i get data in nus_data_handler i am calling pwm init function. and then it is going to
ble_advertising_on_ble_evt...
Hi,
I am wondering if it is possible for a peripheral device to interpret and react to a specific value written to it's CCCD by a central device. In all of the examples...
Hi,
I'm using nrf51822 / sd130 / sdk 12.1.
I am doing minimizing current consumption.
My main function is like below.
I checked no wakeup in sleep mode.
But, current...
What is different between the two hardware versions? I notice there are several examples for the 10028, but not as many for the 10031. What is required to make a 10028 example...
I am trying to get nRF Connect 1.0.0 to bond with my sensor (which uses a nRF52832). This works from several other programs (CySmart on Windows, LightBlue on iPhone), but...
