Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi ,
I'm intrested in using the BLE UART apllication provided by Nordic for the nRF51 422 developpement kit and I have a little question to ask and please forgive its simplicity...
Environment is a PCA10040 v1.1.0, measuring current with a Rigol DS1104B over a 10 Ohm resistor.
I'm using the ble_pwr_profiling example from nRF5 SDK v11. I've programmed...
Hi,
i;m trying to build the "nrf52-ble-app-lbs" example which i downloaded from git hub github.com/.../nRF52-ble-app-lbs.
I followed the instructions in the README file...
I want to connect to the wired sensor NRF51822 board, whether it is possible to adjust the findings for the closure, they sent a message to the application?
Hi, I've recently switched from the older SDK 6 to SDK 9. However, I am unable to get my NRF51822 working with any of the example projects. I've managed to compile the projects...
Hi, I am working on eddystone project i.e nrf5-sdk-for-eddystone-master which is newly released by nordic. And I set URL,UUID and TLM frames successfully but when I trying...
Hello,
I am encountering a very strange problem with the Timeslot API.
I am developing with s130 and using the timeslot example provided by Nordic to
send data revived...
So far I've been prototyping everything on an Arduino Zero connected to a nRF24. Is switching to an nRF51822 an option for me? or will I have to switch my entire code to work...
I need to communicate with several nrf modules, 1 rx and at least 2 rx. I started with nrf24l01 but it has no rssi. For that reason i bought nrf51822.
What i have to do to...
hi,
i have doubt regarding NRF 51822BEACON KIT [pca20006 board],
......i want to configure it in all ble modes [central,periperal,broadcaster,listener],
how can i do...
Hi,
I want to add DFU OTA feature for my project, I use SDK 6.1.0 and S110 7.1.0, I found a sample Bootloader code for different version of SDK (SDK 6.0.0), from Github...
Hello,
I'd like to ask what is the data rate when using BLE OpenMesh network and how much it depends on network architecture.
I'm considering using it in a network consisting...
From the SDK documentation
infocenter.nordicsemi.com/index.jsp
"...platform.h is a use case and
system specific file that can contain
defines and routines needed...
Hello Nordic People,
I am working on making concurrent operation of ESB and BLE to set up sensor network. Currently, the initial set up has been implemented in such that...
Hello,
I use GCC as IDE because I must(though I debug perfectly via Keil v5). I migrated to eclipse GCC by the tutorial published here on 'Devzone'. I added some C codes...
