hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
Can any one Explain me the Following Error
GATT INVALID OFFSET in the Clinet(nrf master control panel APP)
I am getting this error when i try to send more than 23...
Hi,
we are designing a module with the nRF52832 WLCSP. As the module will be soldered on a motherboard a second soldering process respectively a thermal exposure will take...
I would like to load the blinky example on the nRF52 preview development kit. When I try to build the project I will get this error:
Error #541: 'ARM::CMSIS:CORE:3.40.0...
Hello, this question is similar to this questions (Scan request packet, answered by John DeWitt and Aryan)
I'm using
IAR EWARM 7.20
PCA10001 V 2.0.0 ...
We are using nrf51822 AB variant(16kb Ram, 128 kb flash). Due to flash size constraints we are still using s110 softdevice v5. Following is the linker script config:
FLASH...
Hi,
I have setup my system for working with nrf51822 with openOCD and STLink to program it. The blinky went well. But now when i try to program it i get the following error...
I have just concluded a three year development using TI's Tiva ARM M4 chips, writing both bootloaders and applications.
I am using an RFduino to explore BLE.
I have...
Hi all!
Today I run tests in a public place (some Art Design College) and it looks that radio environment, that exists in the place, kills nrf51 completely....
My guess...
Hello.
I want to flash DFU bootloader with keil on chip nRF51822-CEAA (256kB flash, 16kB RAM). I'm using s130
The areas i write to are:
IROM start: 0x3C000
IROM...
I was wondering if it would be possible to add an event for Service Discovery (and other similar BLE stack events) that could be detected by user applications. Per answers...
hello there i have two nrf51 dk kits. now i want that one act as central and other act as server.
i want to communicate between two. can you tell me how to do it??
i think...
hello all:
IN s310 multiprotocol--ble_ant_app_hrm example ,I open the macro BONDING_ENABLE, then i compile,there is a error
......\main.c(674): error: #136: struct ""...
Hello,
At the moment, we test the “Power Off” Mode for lower energy consumption of the nrf52 Preview Developement Kit (V1.0.0) in our project and I have a question about...
