Hi,
i am using SDK v8 with softdevice v8,using master control panel pc application,added custom service and characteristics to application,problem is characteristics value...
There is the board mark on the chip like n51822CEAAD01350A0, where DO is Build code, 1350 is tracking code(YYMM), A0 is lot code.
My question is how can I get those codes...
I'm trying to debug a randomly occuring Hardfault. In trying to trace down the source I read the CPU registers use the Nordic hardfault_implementation.c which grabs the register...
Dear nordic employee
my purpose is send a data the length is from 150 to 273
when my server device send data by sd_ble_gatts_hvx（the send length is fixed 10 bytes） ...
Dear nordic employee：
The service I want to find is the sound service of the thing52 thingy sound service
I tried to modify the HRT_central_client project to find the...
When I was using the device as peripheral, I was wondering when the Softdevice notified BLE_GAP_EVT_SEC_PARAMS_REQUEST and BLE_EVT_SEC_INFO_REQUEST:
1, when peripheral...
hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
I'm trying to figure out why I need to rebond after completing a DFU upgrade with Android 5.1.
My bootloader does not modify the device manager pstorage state, but I am...
Hi!
I've just started developing with NRF51422 (PCA10028 board). I downloaded the free version of Keil MDK-ARM and loaded the "ble_app_uart_s110_pca10028" example from...
Hi,
We wanted to create a device what control with a remote controller but we want to controll this device by smartphone also.
We going to use 51822 but it is not exactly...
Hello.
Our company develop BLE device and make some applications(android/iOS) for updating ble devices.
Those applications use nordic DFU source for installing firmware...
Hi
I want to configure SAADC channel to work in oversampling mode, and to enable burst mode.
nRF52832 Objective Product Specification v0.6.2 says:
"CH[n].CONFIG.BURST...
Hi,
I'm looking to use the nRF51822 in a new design and would like to know if there is tool available to calculate how long it will be able to run of a battery when set to...
I can discover 6 services by Master Control Panel over Android device, but only 4 services on ios 9 device, I can't discover Gap and Gatt service. What's more, when i try...
Hi all,
we are using NRF24L01+ ic for our application .we want to have TAG transmitting and receiving end separated so we are using the two NRF ic .We want that there should...
Hi,
Does Nordic provide a version of nRF Toolbox or similar to run under Windows 8.1 (not Phone)?
If not, can anyone recommend any free general-purpose tools or utilities...
I encounter a problem to switch to DFU mode from UART when BLE is connected and one 5ms timer keeps running for heart rate sensing alg. Maybe it's the reason keeps BLE busy...
Hi,
I want to use BLE to run DFU. My sdk is 8.1.1 and base project is ble_app_uart. When I use nrfgo Studio to program softdevice, bootloader and app, It can't enter app...
I am seeing excessive current in System ON, Idle mode. I am using WFI(). I have verified that
operation is being held at that instruction by using GPIO pin. Idle mode is...
Our manufacturer received new nRF51822QFAAH0 parts. Previously, we were supplied nRF51822QFG2 parts.
According to your PCN_092-1.2 Final.pdf document, there has been a...
Hi,
I can start MCP without the dongle PCA10031 (which I have updated the firmware on) and it starts ok, but when I then plug in and select the device COM 5 - 6xxxxxxxxx...
I would like to ask how to make advertisements which are less than one second. In my application, i need to scan for devices, when i find my specific device, i start to advertise...
