hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Hi,
I want to use the nrf51822 to communicate withe the old module of 24l01p, in the module of 24l01p, the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch...
Hello,
I've been trying to get my TWI device working in conjunction with the BLE stack (i.e. s110 softdevice is enabled) on a nRF51822.
I found another thread with an...
Hi,
I want to use the 51822 to receive data that from the module of 24l01.the Address is
addrofch[0] = 0xe7;
addrofch[1] = 0x7e;
addrofch[2] = 0xe3;
addrofch[3] =...
Hi,
Can any one tell me, what will be the current taken by internal flash of Nordic for
write and read operation and what will be the max time nordic will take to write...
Can someone familiar with the nRF51822 timer infrastructure confirm for me what the maximum achievable PWM frequency is, assuming 8-bit resolution? I've been weeding through...
We got the new sdk and ported the "Alert Notification Profile" to the EVM board. It can communicate with the the Master Control Panel. We want to know whether it can communicate...
hello, on my board the nrf24l01 is optional.
what is the preferred solution to identify if a nrf24l01 is present.
I tried to read the status register. But sometimes...
I am using Laird Bluetooth-4 device BL600 with smartBASIC. While communicating over the I2C bus I am encountering the Hard Pull-up on SDA line. During the Slave ACK I could...
The new pstorage abstraction is almost using 1K RAM, which I'd actually planned to use for something else :-)
Is it possible to limit the RAM used by this module. Can I...
Hi there
can I download the source code?
This app is able to detect the nrf51822 chip even with android 4.1, which is great, so I could test my firmware on my samung...
Hi,
We have a custom board with nRF51822 chipset, We have developed the code to work with some senor peripherals, everything is working fine, but sometimes, when we do testing...
Hi:
chip:nRF51822
code:ble keyboard
How to send the VIRTUAL_CABLE_UNPLUG request by Bluetooth HID devices?
If Virtual Cable Unplug is received by a Bluetooth HID device...
