hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
Hello, I get a compiler warning when I try to log a float value using the LOG_INF macro in my project. The code I'm using is from the cell-fund course: lesson 6, ex. 1. Toolchain...
HI,
I have a function testfun from a customer-provided .a library, and I hope to run this testfun function in RAM. I am currently using NCS 2.8 based on the nRF52840. I...
Hi, I read others cases obout the problem to send more than 20 bytes trhough BLE and add on my prj.conf the next three lines:
This is the entire prj.conf:
Butr when...
NCS 2.7.0
NRF52840 DK
I am trying to trigger an advertising sent callback to indicate advertising timeout or a maximum number of events. I have tried increasing the workqueue...
Im using nrf5340 with nrf connect SDK 2.6.
Im trying to follow this post to evaluate hardware timer for reading saadc
But I constantly am getting
CONFIG_NRFX_TIMER1...
Hi,
I have successfully built and ran the MQTT sample ( /opt/nordic/ncs/v2.7.0/nrf/samples/net/mqtt) on the nRF9160-DK. I did have a few problems with SIM coverage and firmware...
Hi,
running the latest nrfconnect vscode extension (v2024.9.31) the "Add configuration wizard" comes up and stay blank. Additionally, the Actions view is also empty, while...
Hello
I am trying to initialize qspi in a ".cpp" file and methods like
PINCTRL_DT_DEFINE ( QSPI_NODE ); are giving me "out-of-order initializers are nonstandard in C...
Hello,
Currently, I am working on the nRF 52840 DK and the UART port named uart0 is connected to the on board debugger, Where do i find the pins for the UART1 ? I could...
Hi,
I was at the stage to do current measurment on my nrf52DK for my application, but once I cutted SB9 and powered it back by USB, the 4 leds on the board lighted up...
We are planning to base a GATT and LE Audio design off of the latest nRF Connect SDK v2.6.1 and looking into Bluetooth certification. I have found the QDIDs for the Host and...
Hello,
I am trying to use SPI driver to read BMI270 IMU data on my nRF52840dk. I stucked at verifying the sensor ID step. According to the datasheet, sensor ID is stored...
Hello,
I tried to read and write the OTP region in UICR of nRF5340 with nrfutil, but got the following output:
Any Ideas, what could be the issue here? Does nrfutil...
Hello, After consulting the manual and understanding the composition of the calibration data page, the ant_bpwr_calib_handler was added, but the callback function was not...
Hello, I want ro test the channel sounding feature using the new nRF54L15-DK /PDK and I found a sample example for reflector role - "https://docs.nordicsemi.com/bundle/ncs...
