why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
I have implemented a ublox ANNA-B402 on a custom board and am trying to flash code using the debug out header (P19). I am using Segger Embedded Studio and am flashing code...
Hi,
I have twp device: one peripheral and one central. My peripheral is sending out high payload data continiously. And my central is sending data ()in 10Hz frequency. However...
Hello,
I'm interested in increasing the range I can get out of an Isochronous connection between two nrf52832 while maintaining about the same throughput. I'm not concerned...
Good morning,
In our next product (mounting a nRF52840) we will need a dual UART+BLE update channel. We have already implemented the update via BLE and we are now trying...
In SDK v2.6.1, commenting out the following code in websocket.c allows successful connection to the WebSocket. However, in SDK v2.7.0, even after commenting out the same code...
Hello! I have a Nordic nRF52840 BLE dongle, and I want to scan/sniff BLE air using custom BLE parameters: scan window and scan interval. How can I achieve this correctly?...
Hello,
I'm trying to figure out why GPIO 26 and 27 on the nrf9151 DK default to HIGH. I have my SALAE USB scope connected to several pins. When the board resets, only GPIO...
I am using an nRF52840 and nrf52832 to measure distance, but the reported value is almost twice the actual distance . For example, when the actual distance is 1 meter , the...
I would really like to use Bluefruit and make a Long Range connection between Servers and my Central. I know that it is not build in Bluefruit by default, but there must be...
Hello!
I'm using BLE Mesh sensor client receiving messages sent from multiple sensor servers. I used 2 nRF54l15DKs as 2 sensor servers, each sending 9 16-bit float data...
I have a problem with connecting to my device after i disconnect from it. I have tried ubond function, it does not work. This is my disconnect function:
I have a service...
Hello Nordic support,
My application is based on nRF5 SDK for Thread and Zigbee v4.2.0, with Softdevice S140 as I want my application to operate in either in BLE or Zigbee...
I'm trying to setup an SPI communication between an EVK of the Intan RHD2216 and the nRF 52840.
Browsing similar issues, I read the following topics already
I apparently...
