Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
I would appreciate some suggestions on a good development flow to go from an Example to end application
I have nrf52832 on a custom PCB.
I tested several sdk13.0.0 examples...
If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
1. Please solve the problem of high network current registered to nRF9160 (test environment: no network signal)
2. Rf signal: the test current is normal. See Appendix...
Hello,
I implement my own DFU master in nrf52 using SDK11 to replace use of Nordic mobile App. Target to upgrade is also nrf52 but with SDK15.
I have difficulty to get...
Hi,
How do I set the SPIM3 parameter so that MOSI is low after SPIM3 has sent a byte 0x01?
The test environment
DK PCA10056
SDK :sdk17.1
example :spim3
Thank...
Hi,
How to enable NRFX_LOG_INFO?
I ran the following test, but no nrfx log was found
example:D:\nRF5_SDK_17.1.0_ddde560\examples\ble_peripheral\ble_app_uart\pca10056...
Hi
1.Referring to this tutorial, the customer tested the cat-m mode, and the equipment could not be identified by the customer instrument. How to deal with it?
2.nRF9160...
I followed the tutorial videos and when I connected the device using USB, the computer didn't recognize it and it didn't show up in the devices list in VS Code either. pc...
Hi,
I'm working on a project where we are receiving sensor data from a BLE peripheral (BL654), and publishing it to a piece of PC software via UART/ FTDI cable from a BLE...
hello
1.NRF52840 Upgrade APP+BL+SD from SD15.3 to SD17.1.
2.BL use pca10056_s140_ble_debug,APP use ble_app_buttonless_dfu.
3.Program batch file.
nrfutil settings generate...
I have a case where a maximum of 1.4V will be applied to an GPIO pin immediately before the MCU powers up (the voltage enables a boost converter, which then powers up the...
I see this message on my debug output whenever I connect an app to my device. I'm trying to find where the opcodes and status is documented but can't. Can you please point...
Hi, I'm using a nrf5340 custom board. In my program I am using MCUBoot but I would like to know how I can remove the second slot in flash to flash a big program. I'm will...
I have 4 Thread end devices commissioned onto a matter network and want to control these devices from another Thread end device by pressing push buttons. Is this possible...
Hi,
I am having some issues with the Co AP Client and Server on n rf Connect SDK v 2 . 1 . 2 .
I have flashed two n rf 528 40 dev kits with the examples , one with the...
Hi,
I'm using the bare hci_uart example and try to rise the RTS line manually. Therefore I use the API
and added
in proj.conf. The resulting error code is...
As the title indicates, this question is regarding a scenario in which a coordinator needs to be replaced on an already established network. Is it possible to clone a coordinator...
