Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello!
I am trying to sample a digital signal with 12-bits (In a later stage I will need to sample two 12-bits signals). At the moment I am storing the recorded signal...
Hello Nordic team,
I am faced with the problem of developing a custom bootloader which actively pulls FW from an external mass-storage. AFAIK, the SDK only supports OTA...
Hi,
We are using SDK 14.2 with s132 v5.1.0. Reviewing the changelog for newer versions of the SoftDevice, we see:
"Fixed an issue where the application might not receive...
Hi guys,
I am trying to get the PWM rocking. Everything works, but as soon as I define a nrfx_pwm_handler_t in the nrfx_pwm_init, my system crashes with the following error...
Hello Nordic Team,
We are developing a wearable device. We noticed spontaneous BLE disconnections every 1-2 hours. The error code is BLE_HCI_INSTANT_PASSED. I have checked...
We are starting a new wearable device design which will be worn by the user on the chest. We are looking forward to use NRF5340/NRF52840 based modules. The final design is...
hello together,
I would like to use this chip nRF9160-SIAA-B1A-R now only as LTE modem. But the modem should be controlled by two external MCU. Please see figure.
...
Hi support team,
Our purpose is to provide the modules to our customers. We have developped the hardware module based on nrf52832. Now we want to test the BLE mesh functionalities...
I used VDD channel to detected battery voltage, and the P0.5(AIN3) connect to a LED, But I found that after initialize SAADC, P0.5 cannot control output.
Hi Nordic
I have some questions regarding switch to Application on custom address.
The memory layout in flash is like this:
0x00000000 - MBR 0x00000000 - softdevice...
Hi, I am new to the nRF Connect extension in VS Code and I am having trouble including dealy.h header file to utilize a DelayMs() function. I found the delay.h in the sdk...
I am advertising some data, my hardware is minimum and there are no external interrupts.
1. How do I wake up after entering power save mode with __WFE(); ?
2. I also want...
Hi ,
I want to use above PMIC for Gotek tracker. But I have below questions:
1. Due to the IO limitation, can I use static high or low to configure the chip with VOUTB...
Hello,
We are working on a product that has UART and SPI integrated. We initialise the UART and the SPI at the beginning of the code and everything works fine.
However...
I am using the nRF52840 and the pair of Nordic BLE UART Demo projects ble_app_uart_c_pca10056_s140 and ble_app_uart_pca10056_s140
Please can you tell me how to change the...
