As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hello,
Before going into detail, the question is: Is there is any chance that NAND flash will be supported (via QSPI or SPI) by the nRF5 sdk in the future ?
My question...
I made all of the functions using nrf52832, s132. Now I want to reduce the current consumption.
So, I tried changing the slave latency. It was confirmed that the current...
When I combine BLE_APP_UART + BLE_APP_UART_c apps in last step "ble_nus_data_send" return error 4 from BLE_APP_UART part in multirole mode
BLE_APP_UART_c send without problem...
Hi,
I am working on having my device to perform a dfu over spi. I have been able to get through the init packet initialization and transfer, however, I am getting an error...
If my device only acts as a peripheral, does it need to respond to BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST events? In other words, is BLE_GAP_EVT_CONN_PARAM_UPDATE_REQUEST a...
Hello,
I added bonding to my BLE central device so I can re-establish known connections very fast. The bonding of the devices works fine but additionally I would like the...
Hi all,
I am using ncs version 1.5.0 and dk version 0.15.0.
I would like to rely on the CC310 piece of hardware to perform some cryptographic computation.
However, I...
Hello.
I have a question about setting MAC address.
For now, my device uses random static address from FICR.
And I also use "bt_set_id_addr()" function for test purpose...
Hello
I'm having some issues setting up monitor mode debugging with the nrf connect sdk v1.4.99.
I've roughly followed the steps outlined in this guide , the exact steps...
Hello,
I am trying to program my NRF52840 chip with the Secure Bootloader UART project, in addition to the BLE App UART project as mentioned in the title. So far, having...
I am trying to work with Bme680 with I2C communication i can read every value but i cant read air quality value its always at 806516 value and does not change . I thing configirations...
I've been trying to integrate CLI over USB CDC ACM into my project, but I'm failing even to run the SDK example.
CLI works fine over UART, but it won't run over USB.
...
Hi,
My application has hard faults sometimes, and I'm trying to figure out the reason.
When it occurs - I have a hard fault log, but p_stack->pc is 0. I can't understand...
When I use j-link soft uart all good
but when i disconnect j-link the soft uart will error
like this so�rceid=2, status=0 sourceid=3, status=0 sourceid=4, status=0
