I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello, everybody,
I use FDS to write some custom data, when SOFTDEVICE is PRESENT, and i disable the SOFTDEVICE, May I ask if I can still write custom data with FDS?
Hi there!
We are using nRF52840DK development kit with nRF-Connect SDK to build a pre-production version of our product. We have added the required BLE service and characteristics...
Hello, I implemented a firmware based on the multilink central example, with a custom service. I am using NRF52832 (custom board) with SDK v15.2 and Softdevice S132 v6.1.0...
Hi everyone,
I am using the nRF52840 DK and I am experimenting with the USB MSC example. My purpose is to record data from an IMU device and store them in files. Then to...
Hi,
This is a followup from another issue ( link ) which helped with.
The suggestion to modify nrf_serial.c fixed the previous problem, and you can see that the TE (transmit...
I have an expansion board by ST mounting an analog mic (MP23ABS1). The mic out pin (via a diff. amplifier) is given on a connector. I take that signal and feed it to the AIN5...
I'm trying to ensure my firmware goes into power off when it should, and that current consumption is as expected when in power off. However, using PPK2 to measure current...
Hi,
I'd like to use SPI and I2C simultaneously on nRF52832. But I came across this post which says "if you use SPI0, TWI0 is not available". Does this prevent me from...
I took the I2S example from SDK15 and while compiling I am getting the following errors. I tried but I am not able to solve it. The same happen when I have taken twi example...
Hello,
SDK : 16.0.0 Controller : NRF52840
I have 2 app_timer instance, one is used for longer sleep like 24 hours, and other is used to blink led when device is performing...
If you are broadcasting in normal mode, this code will not report an error. But if you are broadcasting in long range mode, this code will cause a FATAL ERR. If you are broadcasting...
I am wondering if it's possible to conduct a serial UART loop back test on nRF. For example, if I use a wire to connect the TX and RX pins together, and send something out...
My understanding is that Thingy:91 HW doesn’t support FOTA update of nRF52 from nRF91 since the reset control line isn’t connected from nRF91 towards nRF52. My understanding...
I am working with the udp example in nrfConnect for the nRF9160
I see that CONFIG_UDP_DATA_UPLOAD_SIZE_BYTES has the value of 10 (bytes of payload). However, I do not see...
