Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hello All
I am working on nrf52832. right now i am try to combine peripheral twi sensor program and ble_app_template. Because in my application use LM6BD temprature sensor...
Hello,
I'm testing the ble_app_att_mtu_throuput example on SDK15.2, I found that the throughput becomes very fast by just changing the 'data_length' from 27 to 251 compared...
Hi,
I notice the brightness playback level cannot be reduced/control by reducing nrf_pwm_sequence_t -> .values.p_common during playback , may I know how to adjust the duty...
hi...........
i am using nrf52832 and a peripheral device . i have merged two programs uart and twi sensor . i am getting the data everything is fine , but after the few...
Using Rigado board, MBD350, I am able to write and test basic application using UART and BLE
using my custome board I get the following error:
NRF_BREAKPOINT_COND; ...
Hi.
I development nRF52832(SDK15.00.00, S132).
I have modified SDK15->examples->ble_peripheral->ble_app_uart->pca10040->s132
I want to unuse uart, So I using app_uart_close...
Hi Sir,
We would like to use 32-bit address flash (MX25L25635F), and we set the " QSPI_CONFIG_ADDRMODE" to "1" to support 32-bit address.
when USB port connect to PC,...
i use the BLE uart example in SDK11.0 to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL...
Hi,
I have an issue with a situation where a client remains connected when not needed anymore, I need to terminate any connection that has been active too long, for example...
Hello,
I used the gzll_host_ack_payload_nrf24le project and gzll_device_nrf24le to test the communiction between two nrf24les over Gazell. The result is that the host could...
Hi,
We would like to add another element to the provisioner. Is there an example how to provision and configure a client element on a provisioner node using the new SDK...
Hi, if the setting of the nrf52832 is shown as below:
Is this possible to happen?
cause when I was trying to use the power profiling example to test the connection mode...
Hello,
the current situation is nrf52832 can not receive the ack payload from nrf24le.
nrf52832 is DEVICE ,using the project from nrf5_sdk13.0.0\exzmples\multiprotocol...
Hello.
I need to compile the bootloader for the nRF51822 chip, using the the nRF SDK version 6.1, and ARM GCC.
I do not have access to Keil.
How can I achieve this?...
