I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Above is my code. I am using Keil uVision5 IDE on Windows 10. I am flashing s132 and then application hex to device using nRFGo.
My goal is to take a square wave as input...
hi,
I am using nrf52832 board,sdk 15.0,soft device s132. i can upload both soft device and bootloader, after that how can i upload my application file .i want use both uart...
Hi all,
I am working on sending messages from nrf mesh app (proxy client) to proxy server ( nrf 52832 DK : running light switch example from nrf5 sdk for mesh v. 3.1.0)...
I am trying to program an external board nRF52810 using debug out on PCA10040. I was successfully able to program an external PCB board with nRF52832 using PCA10040,
but...
Hi folks, I'm receiving a special timestamp over bluetooth, and I want to write it to an external memory. I want the time at which it was written to the memory to be as precise...
I use Nodic sniffer nRF_Sniffer_200_beta3 to capture BLE Mesh packets, but found one strange scenario:
1 if set channel filter 37, 38, 39, can capture 3 packets in channel...
Hi,
going on with the migration from SDK 14.2 to SDK 15.3 it keeps on making trouble. Now the spi_mngr is not working anymore. After changing all calls to perform with extra...
We are using the SPIM driver to support a propriety 1-wire protocol used by a TI LED driver (TLC59731). To do this, we're using the MOSI pin exclusively and, for it to work...
I have been trying to get 125Kbit and 500Kbit coded phy wokring by directly using NRF_RADIO API (no softdevice in use). I have followd for example these instructions, but...
Dear all developers,
I'm currently studying about nRF52832 SoC and prepare to develop low current BLE device.
Before starting, I want to know about idle current consumption...
Hi everyone,
Currently, I am working on my bachelor thesis for creating simple network by using MQTT, BLE-6LoWPAN and nRF52832. I have three nodes of 52832 and one raspberry...
Hello,
I post a question last day, and I can not open it any more now, it always saying "Content is under review"
Even the question has been replied to:
The link:...
I don't use SoftDevice. If I initiate flash partial erase process, my understanding is that the system will do smaller portion of erase, suspend, erase again, until the whole...
I'm developing an application on an nRF52832 revAA that logs data coming from the app_uart module. It logs this data to an SD card using the fatfs library; the code is more...
I need to implement a uint64_t counter that increments every microseconds that I can then read.
I tried to use the timer API and increment the counter in the event handler...
