I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi,
currently I am trying to figure out how to disable the cryptocell hardware after enabling it, because if I enable it and then enter systemOFF, the system still draws...
Hello,
I am using NRF52840 Preview DK, I am running peripheral/SAADC example on the board, I shorted Channel 0 and GND on the board and I am receiving negative values...
Hello
I am using Android and BLE communication with nRF52832 (BLENano2) now.
I am using SDK 15.0.0 with keil uversion.
Central is Android and peripheral is nRF52832...
Hi
Using SD Version 6.1.1 and NRF Version 15.3.0.
Using the following advertising params I can set non-extended advertising
ble_gap_adv_params_t advertisingParameters;...
Hello Nordic support, For long term power profiling of nrf52 hardware, I am using the suggestion given here, that makes use of functions in python script ppk.py: https://devzone...
Hello Nordic Team,
I have an application in development where some bigger files (~20kb) can be downloaded into the device, so they get stored in with the FDS system.
Now...
Hi,
I am using BLE application in NRF52832 board and using NRFConnect app to send custom characteristic service from mobile app to nordic device. But if I am sending a data...
I updated Thingy:52 to firmware version 2.2.0 using the Thingy:52 Android app.
WIth the Thingy:52 running v2.2.0, the WebApp for Thingy:52 can pair with Thingy:52 but it...
Hello Sirs,
We implemented a joint bandwidth test (or speed test) for a radio channel by transmitting notifications.
Parameters set in SDK config:
#define NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
I am following the instructions at infocenter.nordicsemi.com/.../nRF52840_PDK_User_Guide_v1.2.pdf to program a pre-compiled example (blinky).
I have two nRF52840-PDK (PC10056...
Hi, im designing a beacon based on nrf52832, but i have a question about RF section, i´m using 2450AT18B100E chip antenna, and to match it with the nrf52 i'm following the...
Hi,
Trying to investigate eddystone protocol. After compiling and uploading ble_app_eddystone example I see Eddystone BLE device in non-connectable mode.
But after pressing...
I am using NRF52840 DevKit on Ubuntu 18.04 (bionic). I have successfully compiled pc-ble-driver and hex connectivity/softdevice.
I have now download pc-ble-driver-py and...
