Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
hello,
Now i remove pwm_library programming in ble_app_uart_c(central) of SDK15.0 to produce a 125KHz PWM waveform.
But i found the program cann't run in NRF52 DK.
pwm_library...
Environment: nrf52832 , nrf5SDKforMeshv310src , nRF5_SDK_15.2.0_9412b96
0.did the switch_light sample use FressRTOS ?
1.if not use , can i use FressRTOS directly ? does...
Hi,
I have a device with two models, the Generic OnOff Server is located on the second element. When using the "Node Control" to change the "GenericOnOff state" the app...
Hi,
I'm using SDK 13.1, SoftDevice 4.0.5 on nRF52832. I have an app which runs for a long time but will occasionally enter the hardfault handler from an address within the...
Hello,
I try to send multi notification in one connection interval, but I can only send one notification.
Hardware
Peripheral: nrf52832 costumed board (with BMD-300...
Hi,
I'm using nrf52 custom board designed for our project,For this we have P0.09 and P0.10 as rx and tx used for uart, when i configured this two pins as rx and tx it is...
Hi
I am running on a nRF52832 chip with following software stacks
Mesh SDK v3.1.0
nRF SDK v15.2.0
Softdevice v6.1.0
I am working on a use-case where I am processing...
Hi
I want to get a certification. I need your help because I am not currently in DTM mode.
The procedure I checked is as follows.
1. J-LINK , USB to Serial Converter...
Hello to all,
I am using nRF52840 with SES SDK15.0 version. My device is goes into sleep mode after sending data to server. But when woke up device for first reading data...
Hi,
Can someone please tell me in what scenario would a device advertise with two different addresses at the same time?
My device is an nrf52382 based custom PCB...
I am try to register nrf9160 DK sim card, but keep getting fail to fetch error. I had made sure that I am entering correct sim Id and the puk but so far no luck to getting...
Hi,
I am using NRF 52832 S132 sdk 15.2.0.
I am working with example project <install folder>\examples\ble-peripheral\experimental\ble-app_multiperipheral.
I added NUS...
Hi,
I am testing the at_client sample code in the nRF Connect SDK.
I want to change the default AT host com port to uart1 or uart2.
I tried to modify prj.conf but it...
