I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
Hi, I'm trying to use SPI to control an RF module to send audio data from one microcontroller to another. The parts and software I'm working with are:
NRF52 Development...
I'm using SDK 15.0 on an nRF52840 dongle. I've been able to retarget the output functions (outputting through the CDC UART) but so far I can't seem to use getchar() in my...
According to the Online Power Profiler , the Standby time between Crystal start-up and Start radio is ~1 ms; however, we measure a variable amount of time between 0 s and...
HI All,
i m new to this technologies.Now m using NRF52840 DK and sdk as nrf15.2..we have developing the nrf52840 as a beacon scanner to scan the ibeacon details like rssi...
I'm using a Nordic dev board (PCA10040, nRF52832) with modified "Nordic_HRM" firmware sending packets of 20bytes at 100Hz over Bluetooth Low Energy.
I'm using Nordic's heart_rate_collector...
Hello everyone! I have followed the tutorial " Installing a 6LoWPAN enabled Linux kernel and required modules" and i have compiled the UDP client IoT example in order to test...
Hi everyone,
I am using nRF52 which has 52832 on it. Currently, I am working on 2 nRFs and one RPi with MQTT on the softdevice 132. One nRF is the publisher, another one...
I am using pcaboard10028 ,sdk12.3.0 and softdevice s130. I am using proximity example to read battery percentage level,so giving adc input as following:
channel.config.config...
Hi, I'm having problem with UART communication. I use basic UARTE code and I want to send simple data to PuTTy terminal. The problem is whatever I would send i get only 'K...
Hello!
I'm trying to update the bootloader of a nRF52 device OTA. We are using SDK 12.3. The device has our own application flashed, along with what is essentially the bootloader...
Hi Sir,
We want to know about AoA /AoD applications for 52811, and there are some question as below.
1. Is there a difference between BT 5.1 and BT 5.0 from the perspective...
Hi,
I'm implementing quadrature encoder to read motor speed/position. So far I configured a gpio pin where A channel of the quadrature encoder is connected to capture timer...
Hi, I'm now using nRF52DK with Keil and have followed the getting start manual in the Nordic Devzon.
Till now, I completed UART example and want to add ADC function to this...
