Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hello, I'm quite new to both the nRF52832 and the Segger Embedded Studio. I have a college project which involves I2C communication with 2 slaves. I was finally able to set...
Hello,
I am trying to read data from a sensor through sensor TX pin connected to RX pin of nrf51822. Nrf51822 recieves this data through RX pin and sends it via bluetooth...
I am seeing a problem using the nRF52 SAADC with two analog channels enabled in scan mode.
Essentially, channel 0 is measuring an analog signal with gain ~= 15 while channel...
Hello,
I am trying to get the RX interrupt to trigger on the PCA10001 board using the segger debugger as my serial terminal.
My hardware setup consists of a PCA10001...
SDK: v15 SoftDevice: S132 Chip: nRF52832 on BL652 Module
I have a command->response type system. The Central (Android phone) sends a command, and the Peripheral (nRF52 device...
Greetings!
I am using nRF52, SDK14.2, and NUS with MTU = 64. I want to transmit 1000 byte string over BLE upon reception of any character to "nus_data_handler" I have divided...
Hello. I'm just trying to get going with the nRF9160 DK which just arrived.
Using macOS.
Followed Getting Started and then nRF Connect Getting Started Assistant, and everything...
Hello,
I'm currently working on a project that requires data to be stored to an microSD. I'm using a custom board with the nRF52832 chipset and a Molex micro SD card holder...
We are working on a product with a pair of Central and Slave BLE devices that will be sold in pairs. The plan is to have the pairs preconfigured in factory so that the Central...
Hi,
I have an error to download firmware in nRF52840-DK, from output console show it failed at verification on address 0x00000000.
I try to compile the light switch example...
Hello,
I have a total of three nRF9160 DKs. Two are version 0.8.2 and one is version 0.70. The version 0.8.2 DKs only work with iBasis SIMs. When I attempt to use a different...
We are using nRF52840 with sdk 15.0 version & segger embedded studio. We are able to store some small amount of configuration data into flash using FDS. But now we want to...
Good afternoon,
I have been having issues discovering any service within a peer device which i have recently paired with. I am using Nordic SDK 15.2 and softdevice 6.1 on...
