I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hi,
This is more of a bug report than a question, but not sure how to get in touch with engineers outside the forum.
In app_util.h (Using SDK 12.3.0) there are two...
(nRF51 SDK v12.3.0)
The function gcm_init() in gatt_cache_manager.c (BLE Peer Manager Lib) calls ble_conn_state_user_flag_acquire() part of the BLE Connection State Lib...
Dear Nordic,
I bought three nrf52840 dongle.
How i test the mesh i am totally confused how its programmed and how mesh tested with this nrf52840 dongle can you help me...
We are trying to do final optimization of the load capacitors connected to the 32MHz crystal on the nRF52840. A value of 13pF for both capacitors results in a frequency that...
Hi,
Using SDK 15.0 via legacy nrf_drv_power, the nrf_drv_power_sleepevt_init causes fault:
It calls nrfx_power_sleepevt_enable but never calls nrfx_power_sleepevt_init...
I am working with Thread on the nRF52840 and have setup a few nodes and a Border Router 1.0.0 as described in the documentation using Raspberry Pi 3B+.
My sdk is nRF5_SDK_for_Thread_and_Zigbee_v1...
Hi
I was wondering if it's possible to scan for both 1MBPS and CODED at the same time, or should I initiate 2 different scans.
using this configuration initiates error...
Hello,
we developed our electronics with your chip nRF52840, but we have problem with communication throught BLE. We tried our firmware on dev kit with this chip. It was...
Hello,
I am looking for wireless communication solution between two devices with a maximum distance of 5-10m for controlling a speed of the electric-assisted vehicle (basically...
Hi,
I use SDK 12.3.0 with PCA10040 board, and try running experimental_ble_app_buttonless_dfu. It works fine when I use Keil to compile, but doesn't when use GNU. I open...
Hi,
I've tried connecting to the nRF52840 Dongle using nRF connect as explained in : ://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.tools%2Fdita%2Ftools...
Hi, I've been trying to build a custom characteristic and so far I can display a single digit number on my BLE app. My update value function looks like this:
And my add...
I am using SEGGER Embedded Studio to program the nRF51822 module. When I was going through the manual for setting up the environment for SEGGER Embedded studio, I found that...
