Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
Nordic \ nRF5_SDK_12 nrf52832 using 2.0 _f012efa \ examples \ peripheral \ pwm_driver, pwm_driver example
Want to set up two road PWM phase is different, for example, the...
I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
Hi,
I'm working on a Custom Android app which connect to my NRF52 without any security.
This App is based on the UART demo App for Android, but I want that only my App...
I see that nRF52 SDK support the printf() , nrf_log_info() and app_uart_put() that can display data received on PC serial monitor, I'm wondering what's different/advantage...
I want to analyze the power consumption of connection parameter update procedure. How can i get a detailed description about the packet flow of it ? for example, the packet...
Hi all, I'm using sdk11.0.0 signed bootloader and I have custom board with dfu support. The custom board have device type ex:0x01 now I need to change device type to ex:0x02...
Hi all,
i need to read the status on my GPIO where there is a led.
I have configured it like a:
nrf_drv_gpiote_out_config_t configLed = GPIOTE_CONFIG_OUT_SIMPLE(true...
Hi. I'm using nRF51822, SDK12.2.0, S130 as multi-link Central.
#define SCAN_TIMEOUT 10
Time-out is working well when it is Single connection. After 10 second, it stops...
How i can see the performance like the Picture. is allways 0% and had also no time or calls in the execution profile. Breakpoints works.
But when i press F10 (Step over)...
Hi There -
I'm trying to test connection interval negotiation with a central by putting nRF Connect Desktop (Mac) in peripheral mode and requesting a connection parameter...
I have a nRF52840 application that needs to take a complex list of commands from a server.
I have a few options. I could:
code a basic language myself for these commands...
HEllo
I am using the example TWI_sensor_pca10040 with a main.cpp, and I see that there is some sort of error with the logging that I cannot point out. I get this error...
Hi
I'm currently working on the 10028 DK board, which was working flawlessly until I used the J-link RTT Viewer, and pushed the IF BOOT/RESET-button. Now, when I try to...
Hey,
SHORT VERSION:
Timer (every Second) gets started when connecting (BLE with nRF Connect) to my DK (SDK12.2, Softdevice S132). Timer gets stopped when disconnecting...
Hi There,
We have an issue where our project crashes, but the app_error_fault_handler() callback is not being called to help identify the cause of the issue. We are using...
Hello guys.
I'm newbie to embedded programming.
I'm trying to make device that can measure temperature of other objects. I have a variable resistor. The resistor's resistance...
