I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
I am using SPI MASTER example from sdk 7.2.0 with softdevice s110(using spi along with BLE).
In my program I have a requirement of reconfiguring spi pins after using spi...
I see that driver version 1.0.0 was tagged on ghitub: github.com/.../v1.0.0
However, when I visit this page: www.nordicsemi.com/.../38649 , I can only find the 0.5.0 version...
Hi
I use nRF51422 for our products.
In a product line, we check the CWtest mode current consumption current.
I decided the determination value of the CWtest mode current...
Hi.
I'm using nRF51822, S130, SDK10.0.0.
I made a source code as below refering radio_test which is in SDK examples.
But the width of frequency is just 0.2MHz as below...
hi,
so i was coding my program with keil and it reach the 32kb so i had to move to the free IDE Eclipse. for that i followed this tutorial devzone.nordicsemi.com/.../
...
Hi !
I've seen that the Makefile given with the examples changed a lot between SDK11 and SDK12, lots of improvements ! However there's still something I don't get. Why...
What system resources are required when using GPIOTE channels (not the PORT event, the other channels)?
I remember on the nrf51822 there was a long-running PAN, fixed in...
I programmed nRF51822 with S120 softdevice and ble_app_hrs_c application to scan beacons.
It works fine but have one problem.
It scans beacons for about 10 seconds...
hi,
i am working on ble_app_uart_simple_adc example which is referred from the link github.com/.../nrf51-ADC-examples
i flashed the code successfully. and detecting the...
Running the SDK11 example \examples\peripheral\twi_sensor on a NRF52 PCA10040 version dev board and can't get any output from TWI pins. Leaving pins unconnected and using...
Hi,
I am trying to set up the development tools for the NRF52 on my Mac by following this tutorial aaroneiche.com/.../
I am getting the following error when i try to...
Hi
I want to get external acceleration sensor values with SPIM using easyDMA on the sensor interruption (using GPIOTE). then after getting all data, I want to calculate...
Hello,
I have question, I'm actually developing an Android application and try to update the firmware on a device with a DFU process. It work on every mobile device except...
I am using the nrf51422 with softdevice 5144_2.0.1 ,
I set two network number using the "sd_ant_network_address_set" api , network number 0 for ANT+ cadence/heardrate.. network...
Hello,
I was just checking for differences between SDK v11 and v12, more specifically, the differences in the SPI HAL and driver code.
In hal\nrf_spim.h of the v12 SDK...
