Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello All,
I am new to this forum, I have been using nRF51822 for a while, and its a great little BLE chip. I am usinga BLE keyboard to send a key to iphone and I captured...
I WANT COMMUNICATION BETWEEN A NRF51422 AND NRF528321 BOARDS, IN WHICH IN NRF51422 BOARD I WILL MEASURE PWM COUNT(IT IS PHERIPHERAL) AND SEND IT TO NRF528321 BOARD WHICH IS...
Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
Hi,
I'm trying to debug my program after trying out the DFU example (specifically dfu/bootloader/pca10040/dual_bank_serial_s132).
Using my Segger J-Link, I run 'erase...
Hi,
I'm using the nRF52832 QFAAB0 with IAR Embedded Workbench IDE.
I have "nRF5x_MDK_8_5_0_IAR.msi" installed.
Inside IAR i have the device selected as "NordicSemi...
I'm trying to write a small program in mbed that relays incoming UART BLE messages to the USB UART.
What is the proper way to setup notifications?
Right now, if I call ble...
Hi,
Warning: This might be a bit of a rant.
Is there going to be an effort made to make more of the nRF52 hardware drivers compatible with FreeRTOS?
Hopefully constructive...
Hello,
I am starting from ble_app_multilink_central example in SDK11.
Per the comment, when updating the number of central links, RAM setting should also be updated...
Hi,
i am using pca10028 with S130v2
We'd like to use a couple of services as we have to deal with a number of external interfaces.
Sadly we cannot get more than 4 services...
Hi there,
I'd like the ability to hold some data locally then resynchronize once the central reconnects.
Are there any example projects that demo this?
What is the...
Hi,
i am not able to send (write characteristic) from android at a higher transfer-rate than 2.3 kbit/second.
With another Bluetooth LE peripheral i get more than 100kbit...
Hi all, i have a nrf51 Development kit and a nrf51822 smart beacon kit and I want to read them in Matlab using the bluetooth receiver of my laptop. I used the instrumentation...
hi all
i try to write in volatile memory but after the second (the first is ok) writing the nrf8001 response me with 0x84 0x08 0x81 -> Internal Error
i don't know why
please...
Hi, apologies for my ignorance but I'm confused by something. I'm looking to add a PA and was thinking of using the RFAxis RFX2401C like many of those nRF24L01+, PA and LNA...
Hi All,
Please tell is ble mesh is it work for nrf51822 EK, the code is taken from this link: github.com/.../nRF51-ble-bcast-mesh . the code provided in this link, is tested...
We have made a bare minimum prototype with nrf51422 QFN chip following the reference schematic for internal LDO setup in 11.5.1 section of nrf51422_PS_v3.1. It is built on...
Hi,
Am using NRF52 S132 softdevice,
I have a use case like when I press a button , I should turn off BLE. So I enabled an interrupt for button. Whenever this button is pressed...
Hi,
i am using nrf51822 to develop our product. I'll try to describe more details to make you understand more clearly.
STEPS:
While testing my project, I had...
