Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi Nordic,
I've built a ble app with a custom protocol, but am struggling with storing bonds, when running under freeRtos.
What I see:
central app crashes (hardfault...
Hello,
I need to implement Find My Device for nRF52833.
From Sample I could find "samples/bluetooth/fast_pair/Locator Tag" example. I tried to go through it. but I could...
Hi,
1. I am testing nRF54L15 PDK PCA10156 0.8.1 Example is: ncs\v2.8.0\nrf\samples\bluetooth\direct_test_mode 2. Which pins can be used as UART TX and which pins can be...
Hi! Recently, I tried putting my nrf9160dk into SYSTEM OFF mode. The code instantly puts it into SYSTEM OFF mode and waits for a gpio interrupt. The problem however is that...
Hi,
I want to connect LDC2114 to nRF9160. I write the nrf9160dk_nrf9160_ns.overlay and the astri,ldc2114.yaml. I don't know how to set GPIOs in & i2c1 - ldc2114: ldc2114...
I am reaching out to inquire about the support for the indication method in the Nordic nRF52840. Could you please confirm whether this method is supported in the Nordic SDK...
Hi,
I have the following scenario:
nrf5340
SDK 2.1.1
HFCLK: 32Mhz crystal
LFCLK: square wave of 32768 Hz from an external RTC, range [0 - 1.8] Volts
square wave...
Hi,
We are currently starting a project using the nRF52832 as our controller, Segger Embedded Studio 5.42a as our IDE, and nRF5 SDK version 17.0.2.
Project Requirement...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
Trying to set up UART/UART0 for async. I cannot get the uart interrupt config to shut off.
CONFIG_UART_INTERRUPT_DRIVEN =n is set in the prj.conf
In config output...
Hi,
I just got nRF54L15 Development Kit boards. I installed 2.8.0 nRF Connect SDK and toolchain into VS Code. I was using 2.6.1 versions,
with nRF52840 and nRF5340 DK...
I am experiencing a crash during system initialization stage (before main function) on the nrf54l15, with Bluetooth enabled in the proj.conf, using tooling and SDK 2.8.0 with...
Hi, Im designing a custom board using a NRF9160 MCU. From the product specification it operates at a voltage range of 3.0(2.8)-5.5V. I want to use a 3xLI socl2 3.6v (parallel...
Maybe the title doesn't make that clear.
First of all, I have customed my own nrf54l15 board, and I successfully built and run some ncs demos.
Now, I want to do something...
I am working on zigbee network.
I have seen that there is an event for network joining but could not find any event for network disconnection.
If I want to check that...
hi,
i use NCS SDK V2.80,and dk board is nrf54h20.
I now want to combine theUSB HID-KEYBOARD and HID MOUSE into USB composite device.
For example, if I want to add hid...
