Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi all,
I am making a device which involves using nfr52832(PCA10040) to communicate with a NAND flash through spi to store data acquired from the ADC. After all the data...
How to enable semihosting in sdk11 examples?
This works, but I can't port it to examples/periferal/template_project :(
changes:
pca10028/armgcc/Makefile:
adding...
Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic-Team,
I am using the SENSING mechanism on GPIOs to wake up a firmware from SYSTEM OFF. Two GPIOs are used for this and it is crucial for the firmware to detect...
Hi,
I am using bare metal SDK v1.0.0. On my prototype, I want to use BLE softdevice together with SPIM20 peripheral, physically connected to Port 2. Starting from the BLE...
Hi, The docs, at least for the nrf54L series, cannot be access because the 'site is under maintenance'. The following links don't work: https://docs-be.nordicsemi.com/bundle...
So I have two questions. My first is on the impedance matching network on different pcb stackups. So wouldn't I need a different matching network for a different pcb stackup...
I am testing a custom board prototype and having trouble getting I2C to work.
During testing, I was able to observe activity on the SDA line, although it consisted of only...
Hi,
I am using the heart rate sample.
I have connected ground to ground, 3.3v to vdd, SDA to pin 26 and SCL to pin 27. I have 4.7k pullup resistors on SDA and SCL. When...
Hi Nordic team,
I am opening this new thread as a follow-up to my previous question:
https://devzone.nordicsemi.com/f/nordic-q-a/128246/how-to-reach-datasheet-level-2...
Hello Zephyr Community,
I am trying to contribute a new sensor driver for the **AMS AS7341 Spectral Sensor** to Zephyr (using **NCS v3.2.2 / Zephyr**), and I would appreciate...
Hi Team,
We require the detailed procedure for locking and unlocking JTAG access on the nRF54L15 device . Specifically, we are looking for:
Steps to enable JTAG...
Hi,
I am working on a Zigbee coordinator based on nRF52840 using the nRF5 SDK (ZBOSS stack).
My network includes up to ~50–60 devices (both mains-powered and battery-powered...
Hi,
We had connectivity issues on our end for the Message Routing Service webhook since May 13, 2026. It has been restored and tested with the nRF Cloud verification test...
Title:
Hi,
We want to use the nRF9151 as an external LTE modem , controlled from another MCU through UART AT commands .
We have designed our own PCB with the nRF9151...
Hi Nordic team:
If my product has mesh functionality and needs to pass NLC certification and needs to be tested with a PST tool at a testing agency.
Do I need to flash...
Hello Nordic Support,
We are developing a project using two setsof nRF5340 DK with the nRF7002 EK attached. We are trying to achieve coexistence between Wi-Fi in SoftAP...
