dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
I am currently working with the nRF52 DK and have compiled some code to read ADC values. This code works fine with the nRF52 DK but I am having trouble getting it to work...
Hello everyone, I'm developing a wearable device based on nRF52832 which reads IMU (ICM20948) data using TWI.
The problem is that if I try to use the code with a custom...
hello everyone,
in my project i need to advertise the sensor data as well as connecting the BLE TAG . in detail i am using nrf52810 with mpu6050 and i want read the accelerometer...
Hello,
During my evaluation of nRF52840 I discovered an issue which prevents the device from joining a Zigbee network successfully.
I'm using out of the box zigbee/light_bulb...
Hi,
I've installed all by the book watching the installation videos and I have a problem building in VScode
when I try to build with nrf connect app window I get this...
Hello,
To preface, this project was redirected to me and I have very little experience using SoCs. Happy to provide any additional information and apologies for issues in...
Hi!,
I am trying to create an application with BT Mesh using the nrF52840 DK and two nrF52840 Dongles with an OnOff Model Server and an OnOff Model Client respectively....
Hello.
I am new to Zephyr, I know how to digital read the pin which is used as INPUT
#define SW0_NODE DT_ALIAS (sw0)
static const struct gpio_dt_spec DOUTINPUT = GPIO_DT_SPEC_GET_OR...
Greetings,
I'm using NRF52840 with softdevice and nRF5_SDK_17.1.0 on NRF52 DK.
The shutdown_handler in my code is as follows:
There is a secure bootloader from Nordic...
Hi, I am using nRF52832 module as connectivity chip (GAP peripheral, GATT server) with ble_app_uart_pca10040_s112 as source.
I am using nRF connect app to test data communication...
I am currently developing a feature for a BLE module to pass certifications (BL654 Laird, based on nRF52840). My application runs on SDK 15.0.0. I used the "radio_test" module...
My overall goal is to update the percentage of battery left in the advertiser and then either go to a nine second sleep to conserve as much power as possible and then wake...
I am following the instructions to enable micro-ecc support for an example code ( secure bootloader ble s132 pca10040 debug). I am using SDK 17.0.2.
I have successfully...
I'm sorry, maybe it's me, but your SAADC documentation leaves much to be desired, as I was easily able to implement getting readings from a single analog input (non-blocking...
Hi,
Trying to do a very simple thing.
I want to start a new project from a sample project, but I want my new project to be in a different folder
Load nRF Connect...
