Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hi,
How are you?
Could help someone with a ask?
I am designing a plate and I am using like guia the nRF9160 DK. The Layer Stack Manager has configured the Top Layer...
path:
\experimental\cli\cli_agent_router\pca10059\mbr
When I execute "bdb start" in the serial port and then execute "bdb Legacy Enable", the terminal devices that are...
Hi Nordic Team,
My dev enviroment is as follow:
nRF52832(ble central)+ S132+ SES+ SDK 17.0
We are facing an issue regarding local BLE Address . When we are flashing...
Hello.
I am developing a peripheral roll using nrf52832 (S132 v7.0.1, SDK v17.0.0).
I want to know the information of the device that sent the connection request. Also...
Dear Nordic Team Support,
I am testing throughput on different environments, my goal is to stream data from custom-board to Laptop. I have set up some experiments as shown...
Hi all:
I am using nrf52840 hardware. nrf connect sdk.
I am using file system and mcuboot at the same time. When i call ` flash_area_open (id, & pfa);`, i got a wrong...
Hello,
we developed a proprietary protocol on top of IEEE 802.15.4 user zephyr on a nRF52833. Everything was fine with hal_nordic on commit 74b3b21f60aa3dc9a4364ffc28dbb47ad8b699a9...
When I pair the peripheral with a dongle connected to nRF Connect Desktop application, then disconnect and Connect again, the nRF Connect does not remember that it was paired...
I built the SMS sample without changing anything. I am using a Lebara prepaid sim card. I was able to exchange SMS messages from one cellular phone to another. I checked with...
Hello,
For a long range test between the nRF Toolbox Android app and the ble_app_hrs (in nRF5_SDK_17.1.0 package) over the nRF52840-DK. I would need to setup this board...
Hi,
I initiated pin 28 as SCK of SPI as normal condition, and I'd like to switch pin 28 as GPIOTE while receiving a command via BLE.
Basically this is how I achieve...
Hi,
I have loaded a simple application on my nRF52840 that just activates a GPIO as soon as it reaches the main loop.
The SoC is powered externally according to the chapter...
Hi,
We will create a ble peripheral device and also can handle timing-critical uart request. The uart will be always communicating and response time can't be slower than...
Dear DevZone:
I am developing an evaluation board with the nRF9160 SiP model, but I have some doubts with the software. Does nRF9160 SiP come factory preloaded with any...
