I'm using nRF52832 and S132 based on nRF5 SDK v14. I get a error code 4 when I add DFU service refer to the experimental_ble_app_buttonless_dfu . The SDK has changed so much...
Hi,
I'm wondering if I can get current transmitting channel during a connection. So
Is there a way I can directly read current transmitting channel?
If not, is...
This question has to do with the observed "recursivity" of the calls to "app_sched_execute" in SDK13 as described in the previously asked question below:
devzone.nordicsemi...
hi.
How do i do ble_app beacon advertisement to one device(Android phone) whose bluetooth address is known ?? I want that beacons should only be seen in nrf_connect app of...
why use 50ms and 400ms connection interval for testing the maximum data throughput(2M,247byte payload)?
Because 50ms can only send a pdu , and 400ms can send up to 8 pdu...
Hi,
I am using Keil IDE to develop nRF51822 project.
in main(), the command line
APP_SCHED_INIT(APP_SCHED_MAX_EVT_SIZE, APP_SCHED_QUEUE_SIZE);
has Error : L6218E...
Hello,
I'm new to the Nordic SDK and I would like to ask you for help with implementation of PORT events for revision < 3 in "low power" mode instead of "high power" mode...
Hi,
we are using nRF52840 in our project, we also set some configuration like below snapshot
Here it comes 185uA, we want to know what is the overall consumption means...
Hi ,
I am working on the nRF52 Dk Kit and running the example code- found on the folder \ble_central_and_peripheral\experimental\ble_app_interactive. This is command line...
As you will see with my simple files I have followed about 3 different tutorials to get to the point I am at. I am trying to replace the included SALSProbe.ino program with...
Hello,
I'm trying to program an nrf52 PCB I created from Arduino and code studio just trying to upload a simple blink but when ever I try to connect any of my ST-link...
Hello
I have defined the SPI pins in the sdk_config of the ble_app_uart example and compiled the code after adding the dependent drivers from spis project as shown in...
Hello,
when writing content onto the CDC-ACM interface of the nrf52840, I sooner or later always end up in a Segmentation fault.
I'm on nRF52840 and using the SDK v16...
I'm using the nRF52840-DK evaluation software from Segger. I want to add NAND Flash support, so I want to add an SPI interface. I have looked at the example in nRF5SDK160098a08e2...
Hi，we had finished application development on nrf52832 long ago, based on nrf52 sdk 14.0(with softdevice 5.0). But now we get feedback which is a bug has been fixed on sdk...
Hello guys,
I would like to know something more about the scheduler whose implementation can be found under SDK_ROOT/components/libraries/scheduler .
Our idea is to apply...
1. I don't want to call the fds function when enabling or disabling cccd: pdb_write_buf_store, so I did the following:
2. I am in nRF5_SDK_12.3.0_d7731ad in the sdk Routine...
Hi There - I'm very new to electronic design and need help making a key design decision. Specifically I want to know that the performance will not be a problem when writing...
Hi
On some devices we see in the production a shortcut between the BT antenna and the P0.18 pin on the 52811. The cause can be extremely warm weather at the production facility...
Hello,
We are tweaking the TLS connection between nrf91 and mosquitto.
What ciphers does the modem support? Is there a list available?
Best regards,
Vlad
I want to send a byte on Nrf connect app upon receiving an GPIO interrupt using BLE_APP_UART code. I have configured pin P0.10 for the GPIO interrupt. I am using SDK15.2.0...
