hi dear nordic employee:
I tried to build the project ble_app_hrs_c（pca10040） by keil5
but I get an error :
._build\nrf52832_xxaa.sct(7): error: L6236E: No section...
Hi,
I am a bit confused about power consumption when using app_uart_fifo. To save power I put MCU to sleep in between each sent and received byte by using __WFE and __SEV...
Hi! I am building an android app for my project. I am using Proximity , UART and DFU from nrfToolbox app. I have 3 buttons on my home screen dedicated for each of them. I...
Dear Nordic employee:
1、 what do I have?
I have a thingy52 develop kit（nrf52832）
2、what is my purpose?
the quality of thingy52 audio demo is not good（iphone7）...
Hello Nordic,
My development environment:
SDK>> NRF51822_SDK10, SoftDevice>> S130
Example>> ble_app_uart
I am looking forward to your reply!
Thanks.
Best Regards...
Dear friends,
according to "nRFConnect_BLE_User_Guide_v2.0", to set up a local device,i should complete the following steps:
Connect a development kit or dongle to...
Hi
I have add some function call like sd_ble_enable in mesh example, I test to get
then I set the address and all sd_ble_cfg_set is ok
but when I call "sd_ble_enable...
While trying to find out a realistic maximum power consumption target I was searching for the power consumption of the LPCOMP comparator. I've seen a few claims about 0.5...
Hello,
I want to send data from central device to peripheral device. I am currently using nRF52DK.
While sending data from peripheral to central device, data is sent successfully...
hello all,
I buy the Fanstel EV-BC832 V2 and start to paying with it.
I used the IAR ide and Embedded studio (SEGGER) ide for my tests.
First i check the blinky and...
I development nRF52832, I want change mac address.
So I modified nRF5_SDK15.0.0/examples/ble_peripheral/ble_app_uart.
I added code to the examples.
////////////////...
Hi everyone,
I want to program the nrf51822 module with the discovery board stm32f429i-disc1 through ST-LINK programmer in Keil IDE but this error appears: "ST-LINK connection...
Dear DevZone Team,
I am an absolute beginner in the field of mesh networking and hope you could help me getting started. Please bear with me.
I have a bunch of sensors...
Does anyone uses Sloeber to program nRF52? I have an issue, when I add a header nrf_temp.h to the project and using following functions:
The problem appears when I add...
Dear Nordic team,
We are developing a BLE application for IOS and Android. On Android, we utilized your Nordic Scanner Lib to scan Bluetooth devices and it is fine and...
Hi. I am trying to stop advertising after a delay in the UART example using;
sd_ble_gap_adv_stop(???)
What do I put in the brackets? It is asking for a uint8_t called...
Hi,
How to stop freeRTOS xtask using timer and recreate again when needed? I'm currently want to control the blink interval, for example I want to have the led blink for...
I used sdk15.2.
The peripheral sends the public key to the central.I received an exception to public key processing.
code:
case BLE_BITBUTTON_C_EVT_BITBOTTON_M_NOTIFICATION...
Hello Everyone,
Struggling with evaluation of Secure DFU over UART lines. I used the sample project "Secure DFU Bootloader over Serial Link (UART/USB) ", during the previous...
Hello -
Any advice on finding a connector from a standard NFC Antenna to the Molex 051281-0594 connector on the Nordic Thingy:52 Board?
I am trying to find a larger NFC...
