Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
S130, SDK 12.3, ble_app_hrs_c example.
I want to use whitelist function in this example but I can't finish it.
When I run peer_list_get(), it gets all 0xFF, means that...
Hello,
I am looking for (10) pieces of the tiny nRF52810-CAAA for a prototype.
Apparently, distributors do not yet have any stock and the lead time is 14-16 weeks.
Might...
This is probably a very easy question to answer and I apologise for not fining the solution myself but I have been trolling through the documentation for several hours now...
I am doing rapid development for a project, using the nRF52840 DK. Two key features are USB and BLE central role.
I started with the usb_cdc_acm project and am merging in...
Hi all,
I added newliib-nano to my GCC project, when I use new ( std:: nothrow) I got
I add some C++ flags and link flags:
custom-nano.specs:
How should...
Hello everyone!
I have been working on getting data from ADS1299 ( ExG bio-signal sensing). I successfully got data from this IC using STM32F407VG (Cortex M4) and transmitted...
Hi I'm using custom nrf52832 board, SDK14.02 and SES. I want use pwm driver to generate 2 channel pwm wave with custom nrf52832. Everything is working fine in nrf52DK board...
Hi,
I am to update the SD version that I am using, and in the documentation to create a firmware packet with nrfutil states that the table can vbe found with nrfutil pkg...
nRF52832 / SDK V15
Hello,
Is there is way to read the nRF52 flash memory (any location if possible) over UART without uploading a program in the flash memory for that...
Hello ,
I'm trying create a beacon Scanner.
I'm using the s130 protocol stack on the nRF51 DK , namely the nRF51422 SoC and PCA10028.
what I'm trying to achieve is...
I am trying to work through the MQTT-SN Examples that comes with the Thread SDK. When I use the prebuilt image for the Raspberry PI 3 board everything works great however...
Hello,
I use an I2C device to wake up a nrf52 microcontroler.
If I just use the init function
static ret_code_t twi_master_init(void)
{
ret_code_t ret;
const nrf_drv_twi_config_t...
Hi,
I'm using Segger Embedded Studio (with gcc naturally). The standard C++ exception handling doesn't work: exceptions are not caught by exception handler. Is there a way...
I have read a lot of the Dev Zone questions here about the RF Antenna design and read the PCB design guideline tutorials and skimmed some of the white papers. Of course the...
The current example TWI_handler will hang forever is it exits with anything other than NRF_DRV_TWI_EVT_DONE. This can occur if a TWI slave fails to acknowledge the address...
Hi,
Based on the electrical specification of nRF52840's HFCLk, the current consumption seems quite different depends which crystal is being used (attached the screenshot...
