I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5ÎĽA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hi,
Having worked with your software on and off for some time now there are a few things I have noticed that are slightly disturbing when it comes to the SDK.
Usually...
I am doing a register retention gzll transmit code with ADC. But problem is that the ADC value transmitted is always 255, if I connect ground to ADC it would read 247. Why...
Hello,
I am using nRF52480, s140 , SDK_15.0 and using a rscs central example. I used
uint32_t current_time = app_timer_cnt_get(); NRF_LOG_INFO("current_Tick: %02d", current_time...
The function nrf_qspi_cinstrdata_get has logic bug that didn't combine data from both register
https://github.com/NordicSemiconductor/nrfx/blob/master/hal/nrf_qspi.h#L702...
Hi,
I'm trying to notify some sensor data at a constant 25 data packets per second.
If I set the `MIN_CONN_INTERVAL` to `10 and `MAX_CONN_INTERVAL` to `30` it all works...
Hi All,
I am developing a BLE central peripheral application by using ble_app_hrs_rscs_relay (nRF5_SDK_15.0.0_a53641a & s140 softdevice) on nRF52840 DK board.
My issue...
Hi,All
My case is that we need 20 peripherals connect to multilink central and send data to central,then central device need send data to Pc with Uart.
The current situation...
Something easier/faster than this? https://devzone.nordicsemi.com/b/blog/posts/getting-started-with-nordics-secure-dfu-bootloader
The procedure described in that link...
I added bonding/authentication to my application.
I have two characteristics: a "protected" characteristic (cccd_md.wr_auth = 1;) with indications and an unprotected characteristic...
Hello!
I have very strange issue when same firmware works fine if it is flashed using segger debugger and randomly fails (with device restart) when it is flashed using BLE...
We have been using the Nordic PPK to optimise the power usage of our nRF52840 based application - very useful tool.
However, our application changes modes over time (e.g...
I have a local ipv4 network with a Mac laptop. There is a Raspberry Pi Thread border router connected to the network. There is an nRF52840 running the Thread CLI example....
