Hi,
I've been working on a way to detect and prevent replay attacks when beacons are used for sensor data. This is mostly used for home automation sensors, where I have BLE...
Hi,
For our current application we have migrated from SDK 13 to SDK 14. We are using RTOS to handle the functionalities of our application. We replaced our own task for handling...
hello,
I use nrf51822 + S130 + SDK12.2 in my product, nrf51822 work at central + peripheral mode，and i use nrf_duf_flash module for my dfu funtion.
The problem is, i...
I want to communicate Central and peripheral devices with KeyPass. Also I want to generate keypass in Peripheral device. But keypass should to include symbols, low/upper case...
I am using SEGGER Studio on MacOSx.
When use the latest mesh SDK, I can run the light_control example and see the debug log in the Debug Terminal of SEGGER Studio.
However...
Hello,
I'm trying to setup a nRF Cloud Bluetooth gateway using my PC (with openSuse 42.2 64bits and rRF Connect v2.1.0 + nRF Cloud Gateway v0.9.7) and a nRF52 DK and I...
Hello: I am using an NRF51 dongle. Date on the device sticker on the back is 2015.38. Also using nrf51_ble_driver_linux_0.5.0.
I can see/connect to the device I am trying...
Hello,
I am use skylab SKB360 module which are used nRF51822 chip.
I have download sample ble application (S110 or S130 softdevice) but its not advertising. Is there any...
I have a downloaded blinkly project for nRF51 build it and flashed the code on PCA10028 board. Added my own custom library to project to accomplish a feature (For which I...
Dear Nordic Team.
What are different between these two hex file in same example.
nRF5_SDK_11.0.0_89a8197\examples\ble_peripheral\ble_app_beacon\hex\ble_app_beacon_s130_pca10028...
Hey,
I have two nrf52 development board. One is PRX, one is PTX. I try to realize the scenario that:
PTX transmits a number like "100", PRX receives this data "100" and...
nrf51822
SDK v10
SD S110 v8
hello!
My pj is about ANCS+nus+hid mouse sevices.
If my borad had bonded with an iPhone,then download new hex from mdk ,and run.
...
For conventional Bluetooth, if two devices are connected, we can send and receive text/bytes to and from each other. It is generic since the two devices can be from different...
Hi,
I will just reiterate that question again.
I really need to get 32K RAM beacons, but Digi-key apparently has only 16K RAM or v.1.1.0 modules. Could advise where...
I read this post with great interest!
devzone.nordicsemi.com/.../
I'm having a similar problem with my Nordic Beacon application. I followed the advice to switch my...
I am using a nRF51822 to send data to an iOS device.
Because latency is critical to my application, i 've set up a test program that sends a packet every second , using notifications...
I have some questions about the scan response packet.
Can a scan response be sent with a peripheral that is configured to be connectable? IE not a beacon.
I read...
Dear Nordic Team,
Thanks for support.
I am using nRF5_SDK_11.0.0. How can i initialize the softdevice with internal RC oscillator in my source code. I am using the below...
Hello;
I'm trying to get data over the TX pin to be sent to the RX pin on a Raspberry Pi.
I have it working on several boards: The nrf51822 Development Board, the Redbear...
The radio notification tutorial ( devzone.nordicsemi.com/.../) says:
"The distance is the time window before/after the radio goes active. The radio events are radio_on...
I'm slightly bamboozled by the LFCLKCSRC options in the NRF52 datasheet / product specification.
Bit field SRC makes sense. Set to 0 for the internal RC oscillator, 1 for...
