I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
Hi,
On the 3.30 of nRF52832_Rev_1_Errata_v1.5.pdf, the sleep current with LFXO active is 0.5μA higher.
I am using a nRF52832 module with the low frequency crystal oscillator...
Hi,
I'm using nRF52832 on SDK V12.2. I add the connection params in the conn_params_init:
static void conn_params_init(void){
uint32_t err_code;
ble_conn_params_init_t...
Hello I have a few questions
In my project, the nPM1300 fuel gauge example via nrf5340dk works properly. I received information such as V - I - SOC via I2C. Currently I...
We need very fast Wi-Fi transfer rates at times. I have been able to tune the code and Wi-Fi driver settings to get up to 30-35 Mbps which is great. But if I don't throttle...
Hi,
Added a function to the coap_client sample code that executes otInstanceFactoryReset by pressing a button and sets it to factory shipping mode. However, it appears that...
I'm developing a system where I want to connect simultaneously to different BLE and ANT+ sensors. I'm using the nRF5340 DK and I would like to be able to select which sensors...
I have a project that I'm pulling in code from multiple_adv_sets using v2.7.0 and sysbuild.
talks about the opcodes and status being in the spec? https://www.bluetooth...
Hello,
We are designing a board with a npm1300 and a nRF5340. A button is connected to npm1300 SHPHLD.
On short-press, we want the npm1300 to send an interrupt to the...
Hi,
we use our code for beacons for very long time now. Unfortunately producer changed chip.
We were using NRF51802QF with SoftDeviceS130.
Now the chip is NRF52810QCAA...
Hi team,
We tested the nRF7002 with the nRF5340 as the host. Now, our application needs to connect the nRF7002 Wi-Fi module with a custom microcontroller other than Nordic...
Hi everyone,
I'm trying to send updated gyro and acceleration values from MPU6050 continuously by BLE function from nrf52832. I'm currently using the nrf52 development kit...
i am having a bus fault somewhere in my code, i am trying to use addr2line to identify the source code line that it heppens at, for some reason it shows as if the adress is...
Hello,
I am trying to establish communication between the nRF9160 SoC and the nRF52840 on the Thingy:91. I have two arrays: one of 774 bytes and another of 8 bytes. Currently...
Hello,
I am implementing the periodic search for lte managment (using SDK 2.5.2 on a nrf9160).
The periodic configurations in struct lte_lc_periodic_search_cfg is: ...
In the Wi-Fi Fundamentals Course, Lesson 2, Exercise 2 (step 7.2) I found that it is necessary to clear the bssid parameter in the wifi_connect_req_params structure. If it...