Hello,
I want to store temperature samples in flash of nrf51822. I am using pca10028 and sdk 12.2.0.
I have the code for writing,deleting and reading from flash memory....
Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
I am using SDK 16.0.0 and nRF52833. In which TWI (master mode) is not working.
Pressure sensor is connected over I2C. (NRF_DRV_TWI_INSTANCE(0))
Previously I am...
Hi to all!
I'm trying to use the same GPIO to wake up the nrf52810 from system off and also use it to execute some functions. I have this code that is based on the example...
I'm trying to load a program to a custom pcb with a n52832 chip, but shows up this error in the Programmer: Failed to load readback protection status: async task failure for...
Hello,
I am working on a project that modified from ble_app_uart_c, with sdk v16.0, softdevice S140
In my case, I defined an event observer by
NRF_SDH_BLE_OBSERVER(m_ble_observer...
Dear Mate,
I am using bl653_dvk board i followed this link clearly (+) Add DFU support to your application - Software - nRF Connect SDK guides - Nordic DevZone (nordicsemi...
I am working on a project that need to receive extended advertising data, I modify periodic_sync from nrf connect sdk to get the data and it works for my device, but I need...
Hello,
I am testing current consumption of my custom board with PPK. There are some passive components (resistors, mlcc) on the board also with active components (accel...
Dear Nordic,
I want to scan slave devices , so I use TWIM nrfx driver to send zero byte data, I don't got error code, but I don't receive TWIM event too. I found a example...
Hi everyone,
I want to design PCB for nrf52840. Do you have any suggestions before i start?
I used STM32, PIC, Nuvoton and Atmel series IC's in my PCBs. But nrf52840...
Hi There,
I am working on a Door lock system using Nrf 52840 Chipsets having BLE and ZigBee Communication protocol. I wanted to have ZigBee OTA DFU feature in my product...
Hi there,
We are seeing a massive difference in UART current between the same revision 2.0.0 nrf5340 devkits. Below, with the UART enabled with HWFC and only the receiver...
My project is using nRF52840. Early software development used an nRF52840-DK to develop most of the software. Software is based on Zephyr using nRF Connect version 1.6.1....
Subject pretty much says it all. I'm looking for a Zephyr project example that uses PHY CODED. I'm using the nRF52840 with NCS 2.0.2 in the vscode environment. I have things...
