Hello,
I have a question about stack usage. I use nRF51822 SoC, 12.2 SDK & IAR 7.60.1. I am interested in stack usage. Have you done any estimations? Or may be you have...
Hello, I get the
"ERROR: The --family option given with the command (or the default from nrfjprog. ini)
ERROR: does not match the device connected."
message after...
Good morning,
this is Algocraft (www.algocraft.com), an high tech company whose core business is to develop, design and market a wide range of professional systems dedicated...
Hi,
We designed the circuit followed the reference circuit(QFN48), but we always failed in the 8kv ESD test.The CPU always reset while ESD testing.
The 8kv ESD power...
Does anybody got an app inventor2 "project" to communicate with the (Adafruit) Bluefruit LE UART (or SPI) ?
Note: my Android version is 4.4.2 (LE "advertising" not supported...
I've created a Secure DFU client using the multilink central example with S130 and SDK 12.2 (running on PCA10031).
There are a few issues we have trouble with.
The...
Hi,
After successfully managing to preserve our devices bonding information (and custom app context data) across DFU updates, we have a few related questions.
I should...
Hi everyone,
I was wondering if there is any method that I can use to test my development kit's scanning/discovering capabilities.
For example, in Bluetooth Advertising...
Dear ,
I use nRF52833 to transfer audio,but I found that this audio will delay 130ms.
I didn't use 32.768K low frequency crystal, do you think this will affect delay time...
Hello!
Quick question: When a device is connected to the u.FL port (actively transmitting things to the port) on the nrf52840 board, does board (in rx mode) only listen...
hi,
program: 'ble_app_blinky_pca10056-s140'
nRF 52840 dk
keil uvision5 IDE.
with the help of IDE , i could build the code and flash the code on to the board.
but...
Hello
I'm testing nrf52820 longrange speed, but it's faster than my calculations. Will it automatically turn on the fec?
This is my config below.
m_adv_params . primary_phy...
Hello,
I am working on application using nrf52810 SDK version nRF5_SDK_14.2.0_17b948a
Sometimes when i disconnect ble from mobile application and again connect then i...
Hello.
I'm using nRF52833, pca10100.
Can I erase only 16 bytes (or more..)?
I read this explaination , and t here's an erase page partial register, but I don't know...
Hello!
I'm currently working on an IoT device that is supposed to send data to the cloud using MQTT with a TLS layer. We got this working in Norway using LTE-M and the...
Hi,
I am supplying my nrf52840 with5V on VBUS. I know that this does not actually provide the board with power, only the USB interface.
Based on the documentation, I understand...
Hi everyone,
I have connected a potentiometer to a GPIO pin (AIN2) and would like to show the varying values in the battery service.
I was wondering if there's any way...
environment:
SDK14.2 Project: ble_app_uart
I am sure that the problem occurs in uart_module.
Uart use the app_uart_put to send the first byte successfully, then it will...
We have already developed a wireless sensor application based on the ESB protocol.
Now we want to increase the range by adding an nRF21540.
We started by testing the sample...
Hi,
Is there a possibility of race condition when writing and reading using nrf_fstorage_write and nrf_fstorage_read?
I have a very strange bug, when writing to an address...
I am using VScode's extension for nRF connect. I have been using it to flash program with the 52DK and 9160DK previously. Now under the connected devices tab nothing shows...
Hi,
I'm using the GPIO mode of CAF leds module to control led.
LED_EFFECT_LED_BLINK or LED_EFFECT_LED_BLINK2 macro can be used to set the effects of led. But the loop_forever...
