If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Dear Concern,
I am getting MCUboot build errors as shown in the below.
C:\Nordic\v1.5.0>west build -b nrf5340dk_nrf5340_cpuapp -d build_mcuboot bootloader/mcuboot...
Hi,
I have nrF52840 DK rev 2.0.1
switch to VDD, Default, SB40 is cut (confirmed by multimeter)
I have the PPK rev 1.1.1
switch DUT to DK
switch Power to DK
I...
Hi,
is possible use for DFU process as DFU server other device as development kit?
I will use it in street lighting but it not usable with development kit. I would use...
I have a couple of examples that work ok on 9160-dk and use SPI3.
However, if I try to use these on SPI1 or SPI2 I get a device not found error.
I am building with west...
hi,
i am working on timer example in peripheral folder. i am including this example in ble_uart example in ble_peripheral folder. i am getting error " 'NRFX_TIMER0_INST_IDX...
I am using the SHT21 sensor for measuring temperature and humidity, trying to connect it to nRF52840 DK Board using TWI mode.
I am unable to even scan and get the response...
I deleted the flash completely for the bootloader example, then I installed soft device. The softdevice area for nrf52832 is written as 148 kb in the documents. In nrfgo studio...
hi,
i am using working on example "pin_change_int" in peripheral folder.in this example interrupt occurs when there is state change on interrupt pin. how to enable interrupt...
Hi,
Is it possible to upgrade a S112 v6.1.1 softdevice to the S113 v7.2.0 softdevice using BLE DFU?
I am getting the following error right after the SD + BL has been...
Hi folks,
I am playing around with the A-GPS sample.
I am trying to send the fix every five seconds to the cloud. This should be possible according to the webinar last...
At my system (production) there are 6 serial ports and 2 programmer (ARM-Flasher from Segger) connected.
The nRF Connect - Programmer only display 5 COM-Ports and NO Segger...
Hello,
I am starting a new project and we are using the following:
-NRF52840
-SDK v16.0.0
-pca10056 (NRF52849 DK)
After downloading the SDK, I was able to build...
Hi,
I am developing on nRF52840 using SDK version 15.0.3 and Softdevice version 6.11
I have observed that the once you initialize the app_uart using 'app_uart_init(...
