If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Hi all,
I am developing a sidewlk application as a replacement for LoRaWAN recently based on the sidewalk protocol implemented in the nRF connect SDK. I would like to check...
Hello,
We are currently manufacturing products using the nRF52840 with the nRF5 SDK. We are planning to develop new products using the nRF Connect SDK and are currently...
below is my develop environment .
TOOL : VSC - NRF CONNECT SDK 2.6.99 DEV : NRF7002DK
I am currently looking into the BLE GATT structure in NCS.
Since I need to use...
1. am currently using the nrf9161_dk. and have not modified the modem FW in anyway.
2. I am using the vscode extension provided by nordic to build/run this sample
a, i...
Hello, I am trying to migrate from v2.5.0 to v2.6.0. I had subghz working for the sidewalk samples in v2.5.0 but can't seem to get it working in v2.6.0. I don't see any errors...
Dear Nordic DevZone community,
I am currently grappling with a challenge involving the transmission of data from an NRF52 device to the NRF Toolbox app through BLE.
To...
When I build some example (e.g. samples\bluetooth\direct_test_mode) with NRF Connect SDK Toolchain v2.6.0 and NRF Connect SDK v2.6.0, I get the following errors: warning:...
Development is proceeding with VSCode.
We are developing the source by adding an overlay file to the nRF5340 Audio sample source.
If you copy the entire folder, open the...
I am quite new to the nRF SDK. When setting up an nRF project in VSCode, I can build my project but I cannot flash the target.
My target in this case is an nRF52840-DK....
We have unit testing working with the Zephyr Unity/CMock setup, however the test runner (test_runner_generate) ignores preprocessor directives (#ifdef) and removes them when...
I have an application that must manage different ble connection with different device (and so different UUID services). For the scanning and connection I used the bt_scan_filter_add...
I am using a ble+wifi module which is MS12SF1 which has nrf5340+nrf7002. It is connected with a pcb in which there are 2 inmp621 pdm microphones. I have tried integrating...
I have a dongle attached to my Windows PC and it has the nRF Sniffer firmware flashed onto it. I have also installed the nRF Sniffer extension for Wireshark.
When I start...
Hi
I have been able to work with the 'Lighting' demo BLE mesh application using the nRF Connect SDK with Visual Studio Code. I have even been able to add my custom board...
Dear Madam / Sir,
we started developing a new electronic device which uses Bluetooth 5.0 four years ago and are now ready to certify it. However, during testing we had to...
