i set up an coap/iot environment and but i was getting error while compiling code for adc i followed steps from this post devzone.nordicsemi.com/.../ here is the problem
Hi all,
I've developed a broadband vibration energy harvester that is able to pick up uW of energy from just a couple Hz all the way to 150Hz. I'm currently looking for...
We use SDK12.10 Main.c (d:\nordic\5142xx\software\org-sdk12.1\nrf5_sdk_12.1.0_0d23e2a\examples\ble_central_and_peripheral\experimental\ble_app_hrs_rscs_relay.
My question...
Solved: Well, turns out delay and SCK doesnt work well together haha. I imagined the sck signal to be a background thread of some sort. I was wrong.
Hi guys,
at the...
Hi
Im looking for a developer in Denmark to discuss ble technology with. Im trying to get better to understand the technology, because i have some ideas involving beacons...
This system does not work if I enable the third Pipe (Pipe2) .
The system is working without any problem as one RX and two TX (Pipe0 and Pipe1).
The problem on enabling...
Hello,
i have read if not all posts about writing to FLASH while using BLE. But could not find the desirable method.
What i would like to do is to write to flash from...
Hi,
I wanted to setup a network connectivity to nRF5340DK to send RPC messages to remote server(Blockchain Network).
Already I tried to setup OTBR using RPi and nRF52840...
Hi,
We are using NRF52832 as our main processor along with an IMU sensor and a vibration motor. We are wondering if using system on mode as power off state (instead of system...
Greetings,
We are using the NCS for the development of a new product with a custom board based on the nRF52840 MCU.
First, we would like to use the Serial DFU feature...
Hi Nordic community,
I'm trying to generate a 1 MHz base clock with one of the peripheral timer, and in the timer ISR does some GPIO toggling.
I followed the nRF5 SDK...
Hello dear Nordic team,
I'm quite experienced in developing under SDK V15 and V17 but absolutely novice for nRF Connect SDK so my question may seem ridiculos. Hope someone...
Hello,
I have an application and I am using a nrf52833, as soon as i flash my application I am getting a hardfault prior to the main call. As in below snap:
I do not...
Hi,
We are using a custom board with nrf52840 and just started using our own generated keys to sign images with NRF SDK v1.9.1.
We ran into issues when trying to swap...
Hi,
I'm moving a project from SPM to TF-M. I have imported a static library and the board (nRF5340DK) restarts automatically every time the following mycli/main.c function...
Hello
I have a nRF52 based device communicating with Smartphones via an encrypted characteristic (SEC_JUST_WORKS) so pairing is triggered and established.
The encrypted...
I want to interface Lis2DH sensor with nRF52832 board. So, I had build and flash the LiS2DH sample code in nRF connect SDK with the required hardware connections. I have also...
Hi,
I got a issue ,that is when i modify the mtu where sample dir is D:\nRF5_SDK_17.1.0_ddde560\examples\ble_central\ble_app_uart_c,it will return a error :
00> <error...
I am evaluating Nordic nRF52840 Development Kit and a test tracking device from Fanstel SE840F-210.
Can I use these for Asset Tracking with Apple Find My network?
I work...
Hi,
I'm using a custom board with an nrf52832. I can also emulate using an nrf52840dk. I have to compile the bootloader because there is no LF crystal on my custom board...
Hello,
I think some corrections/clarifications are needed for the nrfx 2.10.0 drivers.
In the configuration files (for example: nrfx_config_nrf9160.h) I think the definitions...
I’m at the tail end of my project, and I’m turning my focus to the pairing/bonding issue.
The project includes a Central/Client device that connects to several Peripheral...
