Hey,
I just want to know if anybody sucessfully connected HDMI CEC (One-Wire bus) with the nRF52832.
I would be very grateful if anybody could share the library or give...
As the tittle,can anyone tell me how to save data to the flash with nRF51822 ? I use SDK9.0.0 and S110. before I turn off my machine, I want to save several parameters to...
I use example from SDK 13 ble_app_uart_c.
I changed uuid to my uuid from nrf51 peripherial device. I get event BLE_GAP_EVT_CONNECTED
where made
err_code = ble_db_discovery_start...
dear all,
i need your help.
Where we are:
We use mbed software developer platform.
We have BLE Nano V1.5 + MK20 USB Board V1.0 from RedBear.
We are able to generate...
Hi:
environment:
target board: DK52 board and run LWM2M example of IOT-SDK v0.9
router: ubuntu 16.04 on VM and runs bsserver and LWM2M server on ubuntu 16.04 ...
Hi,
I'm interfacing a nrf51822 and a H8/3294. My question is how much can I drain a the txd pin of the H8/3294. That means my question isn't really about nrf51822.
In documentation...
I have a board populated with the nRF51822 and associated components for the application.
I am able to flash the device successfully and successfully verify the flash. ...
I want to send data from the device to the server in some way.
We plan to connect the device and Android via Bluetooth and connect to the network using Android's 4G line...
Hi
We measured the SPIS waveform and found some issue on tspis, vso.
In nRF52832 v1.4 page 303, the max value of tspis, vso is 19ns but we measured it is around 39ns~49ns...
Hi everyone,
First of all ,Thanks for being such a supportive forum, I ask a lot of questions(I am a beginner to nordic and BLE)
I am using the example given in the sdk...
I am using nRF52832 IC with SDK v15.
I want to sample some data with 3200Hz sampling rate from SPI interface. There is an accelerometer connected via SPI interface. I...
We use nRF52832-QFAA-B0 and we found that PAN16 issue is still present, at least in some corner cases.
It happens when we put the chip in low-power mode with WFI ; at wakeup...
Can anyone help me?
Each service is working standalone.
There are two cases:
1.the BLE can't connect auto by iphone.
2.firmware can't receive notify...
I am hoping there is a Wiegand protocol file i can import into the project so i dont have to write it. Is there a function that has already been done i can import into my...
Hi Everyone
I was trying to get the BLE Uart working with the nrf52840.
Everything works fine, all files are compiling and running, but when i debug the code using segger...
Hi,
I use the peripheral ble_app_uart with nRF52832 (Murata module). The nRF52832 is connected to another MCU, STM32L476, via UART.
P0.5 - RTS
P0.6 - TX
P0.7 - CTS...
Hi.
I am developing a FW for nrf52832 and am using the nrf51 dongle as a testing tool using nrfconnect.
However, this is not working good because the dongle misses notification...
i need use flashwrite in my code, but i found sometims when i write data in flash, the BLE connecting sometimes is borken, i used this funciton flash_word_write(uint32_t ...
I am looking for help in doing a hardware reset. How can this be done? Do I need to make P0.21 active low so that P0.18 is enabled to be in RESET mode? This is for hardware...
To ship custom sensor data generated at 200 Hz from a BLE peripheral to a BLE Central over a GATT service I chose to start with template project in peripheral directory of...
Hi,
I'm using the nRF52 dev kit and try to use it as an Eddystone beacon. More precisely I want to use Eddystone EID and I would like to register the beacon using ECDH....
