If anyone will ever have this error:
When using c++ and singleton the use of operator new is not possible.
I found the solution in this post: forum.arduino.cc/index.php...
Hi I am using Jlink board, when connected to my pc, I can't select nRF5x programming.
Version I am using is 1.20.0.2. I tried the uninstalling everything and installing....
Hi guys,
In the iot sdk in mqtt.h there are typdefs for "mqtt_topic_t " and "mqtt_subscription_list_t".
I'm trying to set several topics (5) and subscribe to them.
...
Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
Hello,
I'm using the off the shelf Asset Tracker V2 and the application is sending GPS position and other sensor measurement at every 2 minutes.
Is there a CONF to change...
Hello developers,
I saw the process of bluetooth scanning from nordic infocenter.
Scanning for advertisers performing legacy advertising
In this picture, I don't understand...
Hello,
I have an application that runs on a 9160 which uses mbedtls (via TFM) to connect to an AWS server. The application is using a CA that you folks have given me in...
Is there a way to change a build configuration after it was created?
I want to change the kconfig fragments it is calling, but I was no able too. I have to delete and create...
I am trying to test TLS communication between TCP server and client so, how I should generate the certificates and how to provision them in TCP server?
Can I use OpenSSL...
Hi, I am using nrf52832 development kit. MCU is waking up with two buttons and I put MCU to system off mode after successful data exchange or timeout. Init settings are like...
Hi,
I am configuring a button and an ISR to handle the events, but the interrupt is not called only when there is a transition.
Is there any other configuration needed...
During the End Of Line test of one of our device, based on nRF52832, we write the serial number of the device in some non volatile registers, specifically CUSTOMER[8] and...
Hello,
We are using the nRF52810-QCAA(QFN32) in a Beacon application. We have seen serious degradation in Radio performance while using the DC/DC vs. the LDO. More than...
Hi Forum,
i've ran into a problem with configure the nrf24l01. I've disabled all ShockBurst functionality (EN_AA = 0). When putting TX Payload into the Fifo the TX_EMPTY...
Hi~
We are going to use the MAC address and UUID as what we have.
I am trying to save the MAC address and UUID through UART, so I don't know what to do.
Currently the...
Hello,
I am trying to make a code running the Ble stack adn the FreeRtos one, i started from the project ble_app_hrs_freertos_pca10040_s132, i've just removed some things...
Hi.
Newbie stuck at installing IDE.
Trying to follow the automatic installation developer.nordicsemi.com/.../gs_assistant.html
Installed nRF Connect for Desktop v3.8...
Hi,
we have nrf52933 custom hardware.
we are flashing application through j-link.
but after every flashing , I need to hard reset the board in order to run the function...
Dear Nordic，
We developed a product based on the nRF52833 chip, with an external antenna, 3dBi gain. Set transmission parameters 100mS interval and 4dBm transmission power...
