Hi,
I am using nrf5832 that is running a coap server example.
I have modified it a little so it reads sensor data via i2c and returns the data using the coap callback.
...
Hi,
I would like to receive some suggestion about finding a CHEAP smartwatch / wristband already available that has these minimal features: BLE (with SDK / GATT profiles...
Compiled with Keil4 software compilation and C of the mixed program, the error is:Branch offset 0x00000228 out of range of 16-bit Thumb branch, but offset encodable in 32...
Hi,
I am currently working on a prototype with Silicon Labs Thunderboard sense. I am looking for a replacement product that has NRF BLE module. All I need is a BLE module...
I would like to hide BLE advertising from normal BLE devices.
And only be able to see such advertising with dedicated scanner.
I was thinking of changing access address...
Im making a project were i have two robots each one with a device connected with a mobile phone. But at same time i want that, when they are near each other they exchange...
Hi all! I am attempting to download a file from a web server to an NRF52832 using the Nordic IoT SDK version 9.0. Are there any good reference librarie? I found a few for...
I am using NRF52840 with SDK15
I am using AES 128 Encryption and am confused on the documentation:
During the encryption operation with nrf_crypto_aes_crypt or nrf_crypto_aes_finalize...
Hello everybody,
I'm currently trying to create a Bluetooth Low Energy Mesh network of multiple nodes that I can control using a Bridge application.
I use a nRF52840...
Hi,
we are developing one prototype where we are using two MCU for different task. we are planning to give common reset button (for customer access) for both the MCU using...
Hello,
I am attempting to create an example project of the Asset Tracker using the NRF9160DK.
I have installed SES using the Toolchain Manager.
I have attempted using...
Hi,
i'm using the nRF5340 DK and SEGGER Embedded Studio V5.50c. Today after starting SEGGER i was asked to perform a firmware restoration for the j-link if the nRF5340 which...
Hi,
I need to use two uarts for the project requirement. UART0 is enabled and working successfully. And I am trying to initialize UARTE, but I am not getting any output...
Hi,
I decided to try the “ble_peripheral/ble_app_gls” example on nRF52-DK.
While I could connect to the kit, pair and bond successfully, when I deleted the device from...
Hi:
I test this hids project, if remove the function bt_conn_auth_cb_register(&auth_cb_display). The iphone will require paired while reconnecting after disconnected. Can...
I am trying to determine the service handle of the nus example, to be able to verify that the central has turned on notifications.
I am using the sd_ble_gatts_value_get...
Hi,
I have a question about 'Thread Secrue DFU',according to the ' https://infocenter.nordicsemi.com/index.jsp ' ,the 'Thread Secrue DFU' does not use softdevice of transform...
Greetings,
CPU = nRF5340
SDK = nRF Connect SDK v1.6.1 and 1.6.0
Board = custom
For the nRF5430, we have a custom board that uses active high logic to turn LEDs on...
Hello,
I am trying to get the nvs driver working on the NET cpu and am having trouble getting the initialization working. The code below is what I am currently working with...
There have been several other posts on this issue dating back a few years, such as this one .
On Windows 10, if I am using SEGGER's RTT Viewer and I flash a nRF52832 with...
Dear,
As the example code is shown, I have been implementing on LED PWM through nRF53 GPIO0 12. If I set the brightness to 100, it was ON without any issue. However, if...
