Hi,
If the following function is used, how to solve this error:
#include <nrfx_reset_reason.h>
void check_and_clear_reset_reason ( void )
{
// 获取复位原因
uint32_t...
2025-06-13T08:43:42.649Z INFO Initialising the bundled nrfutil device 2025-06-13T08:43:42.652Z DEBUG Started watching devices 2025-06-13T08:43:44.400Z INFO Using the bundled...
We are in the process of finalizing the RF transceiver chip for custom protocol development.
Please suggest the suitable chip and any reference implementations available...
Hi all,
we are wondering if there is a clean and reliable way to perform DFU on 54L15 via Thread? Our scenario: once the products get shipped to customers, the border router...
Hello,
We upgraded our project to nrf connect sdk v3.0.2 from v2.9.0 and can no longer use pin 0.00 and pin 0.01 as gpio. The problem seems to be in the nrf53 soc.c file...
Hi I am developing in 54L15. Now use DPPI to link
TIMER10's PUBLISH_COMPARE[3] ---> RADIO SUBSCRIBE_STOP,
it works fine.
Now I want to trigger a GPIO signal through...
Hi Nordic Team,
We are currently developing a product based on the Raytac MDBT50Q-1MV2 module, which integrates the nRF52840 SoC. Our firmware is built using the nRF Connect...
Hi,
I recently wanted to compile this example https://github.com/NordicPlayground/nrf5-ble-tutorial-characteristic?tab=readme-ov-file on another dk to learn about ble development...
Original Title: How to maximize WIFI throughput when using SPI4 between nRF5340 and nRF7002
We are trying to max out the wifi throughput via nRF7002 when connected to...
Hello,
on nrf52811 I want to do advertising once per second. Is it possible using SDK and Zephyr to register an event that advertising was sent - completed? If I understand...
Hello
Is is possible to change the UART pins dynamically? I am thinking to predefine the pins on device tree as follows:
&uart1 {
status = "okay" ;
current-speed...
1. Set up the development environment for the nRF52840 chip in VS Code, but encountered an issue where the chip could not be recognized. The development environment consists...
Hello,
I'm measuring current at the Vbmd jumper for the BMD-350 Eval Board. I'm able to measure 0.9uA running this code:
in the boot immediately after programming...
Hi,
We have experienced some unknown resets in our devices specifically when woken up after being in storage for a prolonged period in ULP mode - about a year or so. Afterwards...
Hello!
I'm writing an application that uses MQTT to post some sensor data to a server. My networking code is basically a duplicate of this sample , except I set up the LTE...
Hello -
I was nearing completion of a BLE Mesh project with the NRF52840 when there became a shortage of NRF52840 QFN. I decided to migrate back to the NRF52832 and reworked...
Hello, I’m testing a circuit built with the nPM1300. When connecting or disconnecting power via USB-C, noise is generated at the circuit's button, causing unintended signals...
I work currently working on a driver module supporting your nRF91x1. I schedule rx-operations via your nrf_modem_dect_phy_rx() dect_phy modem-api. I am using the .handle field...
Hi All,
I am exploring nrf54l15 which has rram 1524KB. However, noticed that not able to access beyond 1428KB.
When build sample hello world code found that only 1428KB...
I've testing out the GNSS and Location samples. According to documentation, A-GNSS is enabled by default in the location sample but I am not able to confirm this both through...
Good Afternoon,
I am working on getting the npm1300 up and running on my custom board. I have a 1v8 line and a 3v2 line with the load switches being used as LDOs. I am using...
