Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
We noticed strange behavior when measuring voltages with the SAADC with our custom board. When VDD_GPIO is at 1.8V (which is our target), the ADC measurement error is about...
Hi, We've been having problems trying to implement a high-speed uart communication between the nRF52832 and an STM32. We switched to using libuarte so we can use DMA even...
I'm running the Nordic/Thread SDK 3.2 with an NRF52840 (Rigado BMD-340) on SES 4.42.
I've got a project using BLE + Thread and I'm having problems implementing a hardware...
A multiperipheral connection to a central, all with custom nordic devices (nRF52840) has been stablished. Comunication and connection work just fine, but after a synchronization...
Hi ! I am represnting company responsible for fruitymesh ( https://github.com/mwaylabs/fruitymesh ) which is an open-source proprietary ble mesh running on nrf5 chips. For...
Dear Support,
I have adjusted the radio test example in SDK16.0 for my custom hardware application using the nRF52840. I have followed the instructions on this page to...
To the kind attention of Nordic support team,
As it was said https://devzone.nordicsemi.com/f/nordic-q-a/57531/sdk16-nrf52810-secured-gazell-keil
the secured gzll library...
Hello,
I'm able to program the code (below) to the nRF52 DK. Leds 17 & 18 are working.
I'm unable to program the code to my custom board. Leds 9 & 10 are not working ...
Is there any problem with beacon advertisment and ADC? I have 3 adc pins configured to measure three different sensors... When i use UART over BLE... everything is ok.. but...
Hi!
I seen video and read manual how to use it, but still not doesn't work.
PPK + PCA10040
on the PPK board I set jumprs to DK (all 3 pcs). USB connected to PCA10040...
Looking through the datasheet, current consumption is provided for the nRF9160 Modem at 3.0V and 3.5V. Is it possible to get information on 5V related current draws? I've...
Hi,
I am using the example nrf5-ble-mpu-simple from nrf5-mpu-examples-master to do the following:
a) send a BLE beacon advertisement (non connectable)
b) periodically...
We are currently having an issue with DFU failing on Samsung A7 a running andorid 6.0.1. We are using nRF Toolbox for BLE (DFU application) and when I try to connect the device...
Good day!
I'm working on Time model fro Bluetooth specification.
Question is about time handler. I can't figure out should I write a separate handler for TAI, or I should...
