Hello, I'm running an example of channel sounding using nRF54L15.
The build is fine, but the following error occurs during flash.
Python is using 3.12.4 version. As you...
Hello,
I'm here again because this time I need to autoconfigure (configuring from inside program, no use of any nrf app) heartbeat destination node and source node.
For...
We have developed an application which uses the nRF9160 together with the same GPS and Ethertronics/Kyocera/AVX antennas as that of the nRF9160-DK . For the LTE antenna, we...
We're trying to measure supply current used by the NRF9151 DK but have discovered that the current measurment connector (P22) only includes current supplied to VDD, and that...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
I'm working on a project involving a USB dongle based on the nRF52840 SDK-2.9.1, which needs to communicate with a sensor (also an nRF52840) and transmit data via USB to PC...
I've tried using LESC without bonding, but iOS displays a pairing dialog. I don't think it is possible to avoid this, so the only way to avoid the pairing dialog is to use...
We are using nRF52832 to develop our product with the ANCS function.
But after bonding with the iPhone and then restart the iPhone, an error message "NRF_ERROR_BUSY" will...
Hi,
I've setup nRF Connect SDK v1.1.0 and I was taking a look at the the peipheral_uart example. I couldn't find any API reference when I searched in the v1.1.0 documentation...
Hello,
I sae that there is the possibility to upgrade the modem via FOTA/OTA application (for example asset_tracker), now without touching the modem could be possible to...
Hello,
Are there any hardware constraints or hard forks in putting an older version of an SDK, such as v11.0.0, on a much newer chip?
I'd like to port SDKv11.0.0 to...
Hello,
Is there any existing firmware where the nRF9160 can act as a coprocessor -- accepting AT commands and the ability to forward LTE data to and from a host application...
Hello, i am a beginner, i am parsing a dimming example. i have two client and server boards, as well as an nRF Mesh application. I can change the brightness of LED by pressing...
Dear Sirs,
I have dveloped application based on the ANT rx HRM example and with nrf52 SD board works perfectly (pca10040(
I would like to move to this application into...
I am using ble_app_gls s130 SDK_11. Is it possible to have pairing with static passkey without bonding? This is because the nRF device will be connected to different smartphones...
I am working on the nr sdk for mesh application,When the nodes conncted to the network , it needs to configured before using nRF mesh app ,My device also configured through...
I am using nRF52840 with nRF5 SDK for Thread and Zigbee 1.0.0 on the nRF52840 development kit.
The Release build of the mqttsn_client example compiles and runs fine.
Using...
To start, this was a functional unit and I had been installing test firmware into it.
As of a couple of days ago while attempting to read and write to my nrf5340-PDK module...
Hello,
I am using pc-ble-driver-py 0.14.1 running on python3.8 and Ubuntu Desktop with nRF52840-Dongle. Dongle is running connectivity_4.1.1_usb_with_s135_5.1.0.hex. Dongle...
Hello,
I would like to understand difference between Manufacturer ID (5 bytes), used in ble_dis_sys_id_t type and Company ID (2 bytes) - used in advertising of manufacturer...
Hello,
we made a custom board using the chip nRF51822 and were able to use the template project in \..\examples\peripheral\template_project to make a button switch the led...
