Hi,
1.How to modify the transmission power of the example direct_test_mode to 4dBm? 2. Please provide Method 1 and modify it using the CONFIG configuration? 3. Please provide...
Previously, I designed a PCB for the nRF52832 chip using the RFANT3216120A5T antenna ( link ). However, I was only able to achieve a very limited Bluetooth range of around...
Hi, I'm relatively new to Nordic microcontrollers and have recently completed the beginner's course. Sorry in advance if I made an obvious mistake.
I am currently trying...
We are running a nrf54l15 board that uses an NFC T2T tag to encode a URI to open an application. We have noticed that sometimes, the current stays higher (~200 uA) after the...
I’ve got a bit of a hardware issue with the nRF52811 UART, receiving DMX data from a Chinese DMX controller.
Standard DMX data-rate is 250Kb/S, so the minimum bit time is...
Hi,
I am using the Nordic UART Service (NUS) peripheral and central on two nRF52840 DKs and I am developing with nRF Connect SDK v3.0.0 .
I can't manage to increase the...
I am getting an occasional softdevice assert on a BLE central device (hub). Both the central and peripheral devices are nRF52840 using Coded PHY and NCS v2.7.0. This error...
I use two nrf51 chips, one of which works as central and second one as peripheral. After the DM_EVT_LINK_SECURED event is generated on the peripheral side I'm starting the...
Is there a way to advertize without having to advertize advertisment flags?
The problem is because of these flags I only have 26 bytes left instead of full 29 bytes. It...
Hi,
I want to add custom characteristic to NRF THINGY:52.
I am getting BLE_ERROR_INVALID_ATTR_HANDLE while I update the value to the characteristic.
Update is done...
Hi, I'm working on a custom board based on the nRF52832. I'm developing on Win 8.1 using the latest version of SES and a J-Link Plus. SDK version 14.1.
I've modifed the CLI...
Hi Support Team,
I am trying to create the custom model - as far as I know there are two types of models possible in bluetooth 5 mesh - SIG defined and vendor specific...
Hello,
I have been playing with sdk 14.0 examples for a while and I wanted to try the Nordic UART ble_app_uart using multiple files (ble init, advertising, sdh separate...
I am writing a combined beacon and mesh node using the mesh SDK v0.10.
When dsm_local_unicast_addresses_set() is called in mesh_evt_handler() , which can be found in nrf_mesh_node_config...
I've sifted through the examples given to me, and none of them seem to explain how to create your own service and add it to the stack. All of the services that are registered...
Hello,
I am working with the nRF-SDK-for-Mesh v0.10.1 I am able to compile and run everything fine. However the DFU example hangs. It looks like a hard fault ( all the...
Dear friends,
As shown in the pic below, my nRF connect won't start. Automatic firmware detection and programming are done.
nRF Connect: v2.2.1, board: PCA10040 AND PCA10036...
When i klick "Erase all" in nRFgo Studio, i allways get this Message
"unable to find or open JLinkARM.dll"
i did already try several hints from this site.
corrected...
Hello,
I will post this question to NDZ first time .
Our customer is in trouble to reduce power consumption at nRF52832.
Our enviornment is below.
CPU: nRF52832...
I am using the ble_app_uart example as my base on a 52840 with sdk 14.1. I have commented out BLE_ADV_EVT_IDLE case in on_adv_evt() function and the BSP_EVENT_SLEEP case in...
